Displays |
| Page | |
The display is dim. | ≥Change “FL Display” in the Setup menu. | 35 | |
The elapsed time displayed is | ≥The displayed play time is converted from the number of frames at 29.97 frames (equal to | — | |
actually less than the play time. | 0.999 seconds) to one second. There will be a slight difference between the time displayed |
| |
| and the actual elapsed time (e.g., actual |
| |
| 59 minutes 56 seconds). |
| |
TV screen and video |
|
| |
The images from this unit do | ≥Make sure that the TV is connected to the VIDEO OUT terminal or the HDMI AV OUT | 9 | |
not appear on the TV. | terminal on this unit. | — | |
Picture is distorted. | ≥Make sure that the TV’s input setting (e.g., VIDEO 1) is correct. | ||
≥If “24p Output” is set to “On” when the unit is connected to a TV through any terminal other | 36 | ||
Jittering occurs. | |||
than HDMI, images may not display properly. In this case, set “24p Output” to “Off”. | 36 | ||
| ≥When “24p Output” is set to “On”, HDMI authentication takes place where 24p images switch | ||
| to other images, and a black screen is displayed. | 36 | |
| ≥When “24p Output” is set to “On”, jittering may occur while playing | ||
| turn “24p Output” to “Off”. | 36 | |
| ≥An incorrect resolution is selected in “HDMI Resolution”, when the TV is connected to HDMI | ||
| AV OUT terminals. While stopped, press and hold [1] and [∫] on the main unit at the same |
| |
| time for more than 5 seconds to cancel this setting. Set the item again. However, Dolby |
| |
| Digital Plus, Dolby TrueHD, and |
| |
| bitstream, select “Restore Default Settings” to restore the factory presets and make proper |
| |
| settings. | — | |
| ≥Picture may not be seen when more than 2 devices are connected with HDMI cables. | ||
| Reduce the number of connected devices. | — | |
| ≥Mobile telephone chargers can cause some disturbance. | ||
| ≥If you are using an indoor TV antenna, change to an outdoor antenna. | — | |
| ≥The TV antenna wire is too close to the unit. Move it away from the unit. | — | |
The screen changes | ≥When the “Screen Saver Function” in the Setup menu is set to “On”, the display may return to | 35 | |
automatically. | the screen saver mode automatically if there is no operation for 5 minutes or more. |
| |
. | ≥An image is not output from the VIDEO OUT terminal when the “High Clarity Sound” is | 33 | |
Video is not output | enabled. Set the “High Clarity Sound” in the |
| |
| terminal. |
| |
|
|
| |
Video is not output in high | ≥High definition video cannot be output through the VIDEO OUT terminal. | — | |
definition. | ≥Confirm that the “HDMI Resolution”, in the Setup menu is set properly. | 36 | |
|
|
| |
The Setup menu cannot be | ≥Select “BD/DVD” or “SD” as the source. | 14 | |
accessed. |
|
| |
Status messages do not appear. | ≥Select “Automatic” in “Status Messages” in the Setup menu. | 35 | |
|
|
| |
The 4:3 aspect ratio picture | ≥Use the TV to change the aspect. Refer to your TV’s operating instructions. | — | |
expands left and right. | ≥When using an HDMI cable, set “TV Aspect” to “16:9”. | 36 | |
Screen size is wrong. |
|
| |
When playing | ≥Connect this unit to the TV with any cable except the HDMI cable. | 9 | |
progressive output, one part of |
|
| |
the picture momentarily |
|
| |
appears to be doubled up. |
|
| |
|
|
| |
There is no apparent change in | ≥The effect is less perceivable with some types of video. | — | |
picture quality when adjusted |
|
| |
with the “Video” menu in the |
|
| |
|
| ||
The | ≥If the “Screen Saver Function” in the Setup menu is set to “Off”, the | 35 | |
in gray. | displayed in black. |
| |
Still pictures (JPEG) do not | ≥The images that were edited on the PC, such as Progressive JPEG, etc., may not playback. | 41 | |
playback normally. |
|
|
Reference
RQT9479
45