Displays |
| Page |
The display is dim. | ≥Change “FL Display” in the Setup menu. | 36 |
The elapsed time displayed | ≥The displayed play time is converted from the number of frames at 29.97 frames | — |
is actually less than the | (equal to 0.999 seconds) to one second. There will be a slight difference between |
|
play time. | the time displayed and the actual elapsed time (e.g., actual |
|
| may display as approximately 59 minutes 56 seconds). |
|
TV screen and video |
|
|
The images from this unit | ≥Make sure that the television is connected to the VIDEO OUT terminal or the | 9 |
do not appear on the | HDMI AV OUT terminal on this unit. | — |
television. | ≥Make sure that the television’s input setting (e.g., AV 1) is correct. | |
Picture is distorted. | ≥An incorrect resolution is selected in “HDMI Video Format”, when the television is | 37 |
connected to HDMI AV OUT terminals. While stopped, press and hold [1] and [∫] |
| |
Jittering occurs. | on the main unit at the same time for more than 5 seconds to cancel this setting. |
|
Set the item again. However, Dolby Digital Plus, Dolby TrueHD, and |
| |
| audio are not output in bitstream. To output the bitstream, select “Default Settings” |
|
| to restore the factory presets and make proper settings. | 37 |
| ≥If “24p Output” is set to “On” when the unit is connected to a TV through any | |
| terminal other than HDMI, images may not display properly. In this case, set “24p |
|
| Output” to “Off”. | 37 |
| ≥When “24p Output” is set to “On”, HDMI authentication takes place where 24p | |
| images switch to other images, and a black screen is displayed. | 37 |
| ≥When “24p Output” is set to “On”, jittering may occur while playing | |
| this case, turn “24p Output” to “Off”. | — |
| ≥Picture may not be seen when more than 2 devices are connected with HDMI | |
| cables. |
|
| Reduce the number of connected devices. | — |
| ≥The unit and television are using different video systems. While stopped, keep | |
| pressing [∫] and [DISC < OPEN/CLOSE] on the main unit for 5 or more seconds. |
|
| The system switches from PAL to NTSC or vice versa. |
|
| ≥The system used on the disc doesn’t match your television. | — |
| ||
| 35 | |
| (“NTSC Contents Output” in the “Picture”). | — |
| ≥[DivX] Images may not be output due to how files were created. | |
| ≥If you are using an indoor TV antenna, change to an outdoor antenna. | — |
| ≥The TV antenna wire is too close to the unit. Move it away from the unit. | — |
Picture stops. | ≥[DivX] Picture may stop if the DivX files are greater than 2 GB. | — |
|
|
|
The screen changes | ≥When the “Screen Saver Function” in the Setup menu is set to “On”, the display | 36 |
automatically. | may return to the screen saver mode automatically if there is no operation for |
|
| 5 minutes or more. |
|
Video is not output. | ≥An image is not output from the VIDEO OUT terminal when the “High Clarity | 34 |
| Sound” is enabled. Set the “High Clarity Sound” in the |
|
| use the VIDEO OUT terminal. |
|
Video is not output in high | ≥High definition video cannot be output through the VIDEO OUT terminal. | — |
definition. | ≥Confirm that the “HDMI Video Format” in the Setup menu is set properly. | 37 |
The Setup menu cannot be | ≥Select “BD/DVD” as the source. | 14 |
accessed. |
|
|
Status messages do not | ≥Select “Automatic” in | 36 |
appear. |
|
|
The 4:3 aspect ratio picture | ≥Use the television to change the aspect. Refer to your television’s operating | — |
expands left and right. | instructions. | 37 |
Screen size is wrong. | ≥When using an HDMI cable, set “TV Aspect” to “16:9”. | |
|
| |
|
|
|
When playing | ≥Connect this unit to the TV with any cable except the HDMI cable. | 9 |
using progressive output, |
|
|
one part of the picture |
|
|
momentarily appears to be |
|
|
doubled up. |
|
|
There is no apparent | ≥The effect is less perceivable with some types of video. | — |
change in picture quality |
|
|
when adjusted with the |
|
|
“Picture” menu in the |
|
|
|
| |
The | ≥If the “Screen Saver Function” in the Setup menu is set to “Off”, the | 36 |
masked in grey. | area is displayed in black. |
|
Still pictures (JPEG) do not | ≥The images that were edited on the PC, such as Progressive JPEG, etc., may not | 44 |
playback normally. | playback. |
|
After choosing “Home | ≥Disconnect the HDMI cable from the TV and reconnect it to a different HDMI | — |
Cinema” in “Speaker | terminal. |
|
selection” with the TV’s |
|
|
remote control, the TV’s |
|
|
input selection also |
|
|
changes. |
|
|
Reference
RQT9464
47