The radio
|
| 9:CH |
|
|
SURROUND MUSIC | ■ | A B VOLUME | ||
| FM/AM |
| THEATER | |
Numbered |
| 9:CH | ||
|
| |||
| buttons |
|
| |
|
|
|
| A B VOLUME |
|
|
|
| , |
, | , | , |
|
|
| ENTER |
|
| |
SRD ENH |
|
| ||
| SFC/EQ |
| H.BASS | |
C. FOCUS, | SRD MUSIC |
| ||
FM MODE |
| |||
|
| |||
SRD MUSIC |
|
| ||
Preparation |
|
|
| |
pTurn off TV while using radio since noise may occur.
pPress [THEATER] to switch the remote control to operate this unit.
Manual tuning
1Press [FM/AM] to select the “FM” or “AM”.
2Press [] or [] to select the
frequency of the required station.
TUNED: Displayed when a radio
| station is tuned. |
ST: | Displayed when a stereo FM |
| broadcast is being received. |
Press and hold [] or [] until the frequency starts scrolling to start automatic tuning. Tuning stops when a station is found.
3Adjust the volume with [AB VOLUME].
w If noise is excessive
Press [FM MODE].
Each time you press the button:
FM: Changes between stereo and forced monaural.
AM: BP1 BP2 BP3 BP4 (BPNBeat Proof)
$
Select between BP1 and BP4 that receives good reception. The FM mode is cancelled when you change the frequency.
w FM frequency step
Preset tuning
Preset channels to make selection simple.
Up to 30 stations can each be set in the FM and AM bands.
Automatic presetting
1Press [FM/AM] to select the “FM” or “AM”.
2Press [] or [] to tune to the
lowest frequency.
FM: 87.9 MHz or 87.5 MHz
AM: 520 kHz
3Press and hold [ENTER].
Release the button when “AUTO FM” or “AUTO AM” is lit on the display.
The tuner presets all the stations it can receive into the channels in ascending order.
p“SET OK” is displayed when the stations are set. The last station to be set is then played.
pThe unit of display is MHz for FM radio and kHz for AM radio when the selector is in FM/AM mode.
p“ERROR” is displayed
Presetting was unsuccessful. Preset manually.
Manual presetting
1Tune to the station (➡ left).
2Press [ENTER].
3While “MEMO” is flashing on the display
Press the numbered buttons or [9 : CH] to select a channel and press [ENTER].
e.g., “2”: [0] ➡ [2] “12”: [1] ➡ [2]
The station occupying a channel is erased if another station is preset in that channel.
Selecting channels
1Press [FM/AM] to select “FM” or “AM”.
2Press the numbered buttons or
[9 : CH] to select the channel.
e.g., “2”: [0] ➡ [2] “12”: [1] ➡ [2]
[Note]
If there is nearby electrical interference during auto tuning the frequency may come to a halt without locating a channel. Turn off the power of the nearby electrical equipment.
w Use FM outdoor antenna if radio reception is poor.
pDisconnect the FM indoor antenna.
pThe antenna should be installed by a competent technician.
[Note]
pDisconnect the outdoor antenna when the unit is not in use. pDo not use the outdoor antenna during an electrical storm.
The step is
1 Press [FM/AM] to select “FM”.
2 Press and hold [w] on the main unit.
After a few seconds the display changes to show the current minimum frequency. Continue to hold the button down. The minimum frequency changes and the step is changed.
To return to the original step, repeat the above steps.
[Note]
Back of
FM outdoor antenna (Using a television antenna)
75 j coaxial cable
(not included)
Antenna plug
RQT8655
Any FM/AM frequencies preset in channels will be changed by this
34 procedure. Preset them again.
the main unit
(not included)
