Manuals / Patton electronic / Computer Equipment / Switch

Patton electronic 2710 user manual PATTON NETLINK-T1 MODEL POWER SUPPLY INTERFACE

Models: 2710

1 23

Download 23 pages 33.47 Kb

Page 23

Image 23

APPENDIX E

PATTON NETLINK-T1 MODEL 2710

POWER SUPPLY INTERFACE

Via Main 5VDC power jack (J1)

Center Pin: +5VDC @ 300 mA

Outer Barrel: Ground

Jumper Position for Power via DC Power Jack (default):

Via Auxiliary Power Supplied to Pin KK on V.35 connector

DC Power supplied to pin KK must be 5VDC ± 5%, 300mA minimum.

Jumper Position for Power via Pin KK:

NOTE: NetLink-T1™ is factory configured to accept power from the enclosed DC wall adapter (See Sections 4.3.1 and 4.3.2 above). If you wish to supply power via pin KK on the interface, you must change the setting of the power supply jumper on the printed circuit board. All power sources must be SELV (Circuit, Safety Extra Low Voltage) specified. (See CENELEC EN60950, Section 1.2.8.5)

Patton Electronics Company

Page 23

Image 23

Patton electronic 2710 PATTON NETLINK-T1 MODEL POWER SUPPLY INTERFACE, Jumper Position for Power via DC Power Jack default

Contents

T1/Fractional T1 CSU/DSU USER MANUALMODEL 2710 Series NetLink-T1Page TABLE OF CONTENTS1.1 WARRANTY STATEMENT Section1.5 INDUSTRY CANADA NOTICE 1.3 RADIO AND TV INTERFERENCE1.4 FCC INFORMATION 1.4.1 FCC ComplianceMonday through Friday 1.6 SERVICE INFORMATION2.1 FEATURES tel 301 email support@patton.com2.3.1 The 2710 as the Interface between the Telco and CPE 3.0 CONFIGURATION3.1 DIP SWITCH CONFIGURATION 2.3 SUPPORTED APPLICATIONSSwitch SW5 DS0 Channel Rate SWITCH SET SUMMARY TABLESwitches SW1, SW2, and SW3 Switch SW4 Line Framing and CodingVT100 Switch SW6 Clock ModeSwitches SW7 and SW8 Line Build Out 3.2 SOFTWARE CONFIGURATIONHELPFUL HINTS 3.2.1 Introduction to Main Menua Line FormatESF default Options ESF, D4, UNFRAMED 3.2.2 System Configurationc DS0 Line Rate 64kbps default Options 64kbps, 56kbps b Line Coding B8ZS default Options AMI, B8ZS, B7ZSf ESF Data Link ANSI T1.403 Options ANSI T1.403, AT&T TR54016 g ESF Carrier Loops Enabled default Options Enabled, DisabledOptions Network, Internal, External 15.0 dB -22.5 dBj Default Config Source EEPROM Option EEPROM, Switch h Remote In-band Loops Enabled default Options Enabled, Disabledi V.54 Loops Enabled default Options Enabled, Disabled c spacebar 3.2.3 System Diagnosticsa Local Loop Idle default b Remote Loop Idle defaultNI STATUS c Test Pattern Idle default Options Idle or Sendingd Error Insertion Off default Options On, Off e Selected PatternRx PRM Error CountersCurrent DIP Switch Settings Valid Interval Count & Current Interval Timee Service Information b Passwordc Loop Timeout d Set to Default Configuration4.3.3 Supplying Power via pin KK 4.3 POWER CONNECTION4.3.1 Using the AC Power Supply 120VAC or 100-240VAC 4.3.2 Supplying DC Power5.1 LED DESCRIPTIONS 5.2.3 Central Office Loops 5.2 LOOP V.54 & TELCO DIAGNOSTICS5.2.1 Operating Local Loopback LL 5.2.2 Operating Remote Digital Loopback RLDiagnostics 5.3 BIT ERROR RATE V.52 DIAGNOSTICSd Error Insertion to ON PATTON NETLINK-T1 MODEL SPECIFICATIONSPATTON NETLINK-T1 MODEL CABLE RECOMMENDATIONS Wire GaugeAPPENDIX C PATTON NETLINK-T1 MODEL FACTORY REPLACEMENT PARTS AND ACCESSORIESPATTON NETLINK-T1 MODEL INTERFACE PIN ASSIGNMENT RS-232 Control Port Signals at DB-25 ConnectorRS-232 Control Port Signals at DB-9 Connector M/34 Connector, Terminal InterfaceCopyright Patton Electronics Company All Rights Reserved PATTON NETLINK-T1 MODEL POWER SUPPLY INTERFACEJumper Position for Power via DC Power Jack default Jumper Position for Power via Pin KK

PATTON NETLINK-T1 MODEL 2710

Jumper Position for Power via DC Power Jack (default):

Jumper Position for Power via Pin KK:

Copyright © 2006