Voice connectivity | Patton electronic 4630 Series guide

SmartNode 4630 Getting Started Guide	B • Specifications

Note Refer to the software feature matrix for the most up-to-date speciﬁcations.

DSP

One or two 4-channel DSP

Voice connectivity

3 or 5 ISDN BRI S0 (S/T), 4-wire RJ45 ports NT/TE conﬁgurable per port Point-to-point, point-to-multipoint conﬁgurable

Life-line bypass relay between BRI 0/0 and BRI 0/1 ports

ISDN line power can be switched on per software per port

Data connectivity

Two 10/100Base-TX Ethernet ports

All ports full duplex, autosensing, auto-MDX

Voice processing (signalling dependent)

Four or eight full-duplex channels with Voice CODECS:

•G.711 A-Law/µ-Law (64 kbps)

•G.726 (ADPCM 16, 24, 32, 40 kbps)

•G.723.1 (5.3 or 6.3 kbps)

•G.729ab (8 kbps)

•Transparent ISDN data

G.168 echo cancellation (25 ms)

Four or eight simultaneous low-bandwidth voice or T.38 fax calls

DTMF detection and generation

Carrier tone detection and generation

Silence suppression and comfort noise

Adaptive and conﬁgurable dejitter buffer

Conﬁgurable tones (dial, ringing, busy)

Conﬁgurable transmit packet length

RTP/RTCP (RFC 1889)

DSP

44

Image 44

Patton electronic 4630 Series manual Voice connectivity, Data connectivity, Voice processing signalling dependent

Contents

SmartNode 4630 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Contacting Patton for assistance Cabling List of Figures List of Tables Structure About this guideAudience Precautions Safety when working with electricity General conventions Typographical conventions used in this documentGeneral observations Node Chapter contents General information SmartNode 4630 overview SmartNode SmartNode 4630 rear panel BRI 0/0 60 Hz Reset BRI 0/1BRI 0/2 BRI 0/3 Run PowerSmartNode 4630 front panel VoIP Link BRI Link/SigEthernet Link Ethernet 100M Applications overview Introduction Application-Edge intelligence of enterprise communication Application-Multi-service Isdn Internet telephony IAD How it works Applications overview SmartNode installation Planning the installation Network DiagramSite log Network information Installing the gateway router Connecting the 10/100Base-T Ethernet LAN and WAN cables Connecting the power supply Initial conﬁguration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PC Factory-default IP settings LoginConﬁguring the desired IP address Changing the WAN IP address Connecting the SmartNode to the network Connecting the SmartNode to the network Loading the conﬁguration optional Bootloader Start BootloaderStart-up with factory conﬁguration Load a new application image SmartWare via Tftp Optional RedBoot load -r -v -h host -b Xmodem ymodem -b RedBoot load -r -v -mLoad a new application image SmartWare via the serial link Additional information Contacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information Out-of-warranty service RMA numbers Appendix a Compliance information Safety ComplianceRadio and TV Interference CE Declaration of Conformity Isdn compliance Appendix B Speciﬁcations Data connectivity Voice processing signalling dependentVoice connectivity Voice routing-session router Voice signallingFax and modem support IP services ManagementSystem Physical Identiﬁcation of the SmartNode devices via Snmp SmartNode Model SysObjectID Appendix C Cabling Connecting a serial terminal Console Typical Ethernet straight-through cable diagram Ethernet Isdn BRI Appendix D Port pin-outs Console port Isdn BRI 0/0 NT/Net or TE/User port Isdn BRI 0/1 . /3 TE/Usr or NT/Net Appendix E SmartNode 4630 factory conﬁguration Introduction Appendix F End user license agreement End User License Agreement Termination Other licenses