SmartNode Model SysObjectID | Patton electronic 4630 Series specification

SmartNode 4630 Getting Started Guide	B • Specifications

Operating humidity: up to 90%, non condensing

Identiﬁcation of the SmartNode devices via SNMP

All SmartNode devices have assigned sysObjectID (.iso.org.dod.internet.mgmt.mib-2.system.sysObjectID) numbers (see table 6).

Table 6. SmartNode Models and their Unique sysObjectID

SmartNode Model	SysObjectID

SN4634	.iso.org.dod.internet.private.enterprises.patton.products.sn46xx.1
	1.3.6.1.4.1.1768.2.4.9.1

SN4638	.iso.org.dod.internet.private.enterprises.patton.products.sn46xx.2
	1.3.6.1.4.1.1768.2.4.9.2

According to table 6, an SNMP get request to .iso.org.dod.internet.mgmt.mib-2.system.sysObjectIDof a Smart- Node 4634 device reads out a numeric OID of 1.3.6.1.4.1.1768.2.4.9.1, which represents a SmartNode 4634 device. The mapping of the sysObjectID to each of the SmartNode model is realized with the Smart- Node product identiﬁcation MIB.

The SNMP agent running in SmartWare is SNMP version 1 (SNMPv1) compliant. SNMP version 2 (SNMPv2) and SNMP version 3 (SNMPv3) are not currently supported.

IMPORTANT

Identification of the SmartNode devices via SNMP

47

Image 47

Patton electronic 4630 Series manual Identiﬁcation of the SmartNode devices via Snmp, SmartNode Model SysObjectID

Contents

SmartNode 4630 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Contacting Patton for assistance Cabling List of Figures List of Tables Structure About this guideAudience Safety when working with electricity Precautions General conventions Typographical conventions used in this documentGeneral observations Node General information Chapter contents SmartNode SmartNode 4630 overview BRI 0/0 SmartNode 4630 rear panel BRI 0/3 60 Hz ResetBRI 0/1 BRI 0/2 Run PowerSmartNode 4630 front panel Ethernet 100M VoIP LinkBRI Link/Sig Ethernet Link Applications overview Application-Edge intelligence of enterprise communication Introduction How it works Application-Multi-service Isdn Internet telephony IAD Applications overview SmartNode installation Network information Planning the installationNetwork Diagram Site log Installing the gateway router Connecting the 10/100Base-T Ethernet LAN and WAN cables Connecting the power supply Initial conﬁguration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PC Changing the WAN IP address Factory-default IP settingsLogin Conﬁguring the desired IP address Connecting the SmartNode to the network Connecting the SmartNode to the network Loading the conﬁguration optional Load a new application image SmartWare via Tftp BootloaderStart Bootloader Start-up with factory conﬁguration Optional RedBoot load -r -v -h host -b Xmodem ymodem -b RedBoot load -r -v -mLoad a new application image SmartWare via the serial link Additional information Contacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information RMA numbers Out-of-warranty service Appendix a Compliance information CE Declaration of Conformity SafetyCompliance Radio and TV Interference Isdn compliance Appendix B Speciﬁcations Data connectivity Voice processing signalling dependentVoice connectivity Voice routing-session router Voice signallingFax and modem support Physical IP servicesManagement System SmartNode Model SysObjectID Identiﬁcation of the SmartNode devices via Snmp Appendix C Cabling Console Connecting a serial terminal Ethernet Typical Ethernet straight-through cable diagram Isdn BRI Appendix D Port pin-outs Isdn BRI 0/0 NT/Net or TE/User port Console port Isdn BRI 0/1 . /3 TE/Usr or NT/Net Appendix E SmartNode 4630 factory conﬁguration Introduction Appendix F End user license agreement End User License Agreement Other licenses Termination