Manuals / Patton electronic / Computer Equipment / Network Router

Patton electronic 4630 Series manual Contacting Patton for assistance, Compliance information

Models: 4630 Series

1 59

Download 59 pages 6.13 Kb

Page 5

SmartNode 4630 Getting Started Guide	Table of Contents

	2. Configuring the desired IP address	30
	Factory-default IP settings	30
	Login	30
	Changing the WAN IP address	30
	3. Connecting the SmartNode to the network	31
	4. Loading the configuration (optional)	32
	Bootloader	33
	Start Bootloader	33
	Start-up with factory configuration	33
	Load a new application image (SmartWare) via TFTP	33
	Load a new application image (SmartWare) via the serial link	35
	Additional information	36
5	Contacting Patton for assistance	37
	Introduction	38
	Contact information	38
	Patton support headquarters in the USA	38
	Alternate Patton support for Europe, Middle East, and Africa (EMEA)	38
	Warranty Service and Returned Merchandise Authorizations (RMAs)	38
	Warranty coverage	38
	Out-of-warranty service	39
	Returns for credit	39
	Return for credit policy	39
	RMA numbers	39
	Shipping instructions	39
A	Compliance information	40
	Compliance	41
	EMC	41
	Safety	41
	PSTN Regulatory	41
	Radio and TV Interference	41
	CE Declaration of Conformity	41
	ISDN compliance	42
B	Specifications	43
	DSP	44
	Voice connectivity	44
	Data connectivity	44
	Voice processing (signalling dependent)	44
	Fax and modem support	45
	Voice signalling	45
	Voice routing—session router	45
	IP services	46
	Management	46
	System	46
		5

Image 5

Patton electronic 4630 Series Contacting Patton for assistance, Compliance information, Specifications, Table of Contents

Contents

ISDN BRI S0 VoIP Gateway Router SmartNode 4630 SeriesGetting Started Guide Sales Ofﬁce +1 3017622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents Summary Table of Contents Table of ContentsTable of Contents SmartNode installationTable of Contents SpecificationsContacting Patton for assistance Compliance informationCabling SmartNode 4630 factory configurationPort pin-outs End user license agreementList of Figures Factory default IP address and network mask configuration List of TablesGeneral conventions Rear panel portsStructure About this guideAudience Safety when working with electricity PrecautionsGeneral observations Typographical conventions used in this documentGeneral conventions Commands and keywords are in boldface fontConvention Indicates the names of command buttons that execute an actionMeaning SmartNode 4630 Getting Started GuideChapter 1 General information Chapter contentsSmartNode 4630 overview WAN ETH 0/0 SmartNode 4630 rear panelLAN ETH 0/1 BRI 0/0BRI 0/1 ResetBRI 0/2 BRI 0/3Description SmartNode 4630 front panelPower VoIP Link DescriptionBRI Link/Sig BRI B1/B2Chapter contents Chapter 2 Applications overviewApplication-Edge intelligence of enterprise communication IntroductionHow it works Application-Multi-service ISDN Internet telephony IAD2 Applications overview Application-Multi-service ISDN Internet telephony IADSmartNode 4630 Getting Started Guide Chapter contents SmartNode installationChapter Create a network diagram see section “Network information” on page Planning the installationVerify power source reliability see section “Power source” on page Network DiagramPower source Installing the gateway routerInstalling cables Software toolsConnect the cables in the following order Connecting ISDN terminals and NT to the SmartNode’s ISDN BRI portsConnecting the 10/100Base-T Ethernet LAN and WAN cables Do the following to connect the main power to the Model Connecting the power supplyInternal S-Bus power supply Chapter Initial conﬁgurationChapter contents Introduction 1. Connecting the SmartNode to your laptop PCConnecting the SmartNode to your laptop PC Login Factory-default IP settings2. Conﬁguring the desired IP address Changing the WAN IP address3. Connecting the SmartNode to the network 4. Loading the conﬁguration optional Start Bootloader BootloaderStart-up with factory conﬁguration Load a new application image SmartWare via TFTPDownload it after starting up SmartWare with the following command Command Load a new application image SmartWare via the serial linkRedBoot load -r -v -m StepAdditional information Additional informationChapter contents Chapter 5 Contacting Patton for assistanceWarranty coverage Warranty Service and Returned Merchandise Authorizations RMAsContact information Patton support headquarters in the USAReturns for credit Out-of-warranty serviceReturn for credit policy RMA numbersChapter contents Appendix A Compliance informationCompliance SafetyRadio and TV Interference CE Declaration of ConformitySmartNode 4630 Getting Started Guide ISDN complianceA Compliance information ISDN complianceChapter contents Appendix B SpeciﬁcationsData connectivity Voice processing signalling dependentVoice connectivity Voice routing-session router Voice signallingFax and modem support Power Consumption 10W Operating temperature 32-104F 0-40C IP servicesManagement SystemOperating humidity up to 90%, non condensing Identiﬁcation of the SmartNode devices via SNMPSmartNode Model SysObjectIDChapter contents Appendix C CablingNote See section “Console port” on page 53 for console port pin-outs ConsoleIntroduction Ethernet EthernetISDN BRI ISDN BRIChapter contents Appendix D Port pin-outsISDN BRI 0/0 NT/Net or TE/User port Console portIntroduction EthernetPin Signal ISDN BRI 0/1 .. 0/3 TE/Usr or NT/NetChapter contents Appendix E SmartNode 4630 factory conﬁgurationIntroduction The factory conﬁguration settings for SmartNode 4630 are as followsIntroduction Chapter contents Appendix F End user license agreementEnd User License Agreement 5. Warranty1. Deﬁnitions 2. Title7. Other licenses 6. Termination