Isdn BRI 0/1 . /3 TE/Usr or NT/Net | Patton electronic 4630 Series

SmartNode 4630 Getting Started GuideD • Port pin-outs

Table 8. RJ-45 socket

Pin Signal

5Tx-

6Rx-

Note Pins not listed are not used.

Note All pins between the port BRI 0/0 and the port BRI 0/1 are connected during power failure. Fallback relay operation:

•When the unit is not powered, the fallback relay connects pins 3, 4, 5, and 6 of the net and the user ports (fallback) together. This enables you to place calls to the PSTN even if the unit is powered down.

•Line power applied to the Line port is fed through to the Phone port at all times and independent of the fallback relay’s status.

Note On each ISDN BRI port in TE mode, it is possible to switch on ISDN line power per software. The total amount of power is 4W. If a ISDN BRI port is switched to NT mode, the ISDN line power is turned off.

ISDN BRI 0/1 .. 0/3 (TE/Usr or NT/Net)

The BRI Line port uses an 8-pin RJ-45 connector (the pinout is shown in table 8).

Table 9. RJ-45 socket

Pin	Signal

3	Rx+

4	Tx+

5	Tx-

6	Rx-

Note All pins between the port BRI 0/0 and port BRI 0/1ports are connected during power failure.

Note On each ISDN BRI port in TE mode, it is possible to switch on ISDN line power per software. The total amount of power is 4W. If a ISDN BRI port is switched to NT mode, the ISDN line power is turned off.

ISDN BRI 0/1 .. 0/3 (TE/Usr or NT/Net)

54

Image 54

Patton electronic 4630 Series manual Isdn BRI 0/1 . /3 TE/Usr or NT/Net

Contents

SmartNode 4630 Series Mailsupport@patton.com Summary Table of Contents Table of Contents Contacting Patton for assistance Cabling List of Figures List of Tables About this guide AudienceStructure Precautions Safety when working with electricity Typographical conventions used in this document General observationsGeneral conventions Node Chapter contents General information SmartNode 4630 overview SmartNode SmartNode 4630 rear panel BRI 0/0 BRI 0/2 60 Hz ResetBRI 0/1 BRI 0/3 Power SmartNode 4630 front panelRun Ethernet Link VoIP LinkBRI Link/Sig Ethernet 100M Applications overview Introduction Application-Edge intelligence of enterprise communication Application-Multi-service Isdn Internet telephony IAD How it works Applications overview SmartNode installation Site log Planning the installationNetwork Diagram Network information Installing the gateway router Connecting the 10/100Base-T Ethernet LAN and WAN cables Connecting the power supply Initial conﬁguration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PC Conﬁguring the desired IP address Factory-default IP settingsLogin Changing the WAN IP address Connecting the SmartNode to the network Connecting the SmartNode to the network Loading the conﬁguration optional Start-up with factory conﬁguration BootloaderStart Bootloader Load a new application image SmartWare via Tftp Optional RedBoot load -r -v -h host -b RedBoot load -r -v -m Load a new application image SmartWare via the serial linkXmodem ymodem -b Additional information Contacting Patton for assistance Warranty coverage Contact informationPatton support headquarters in the USA Out-of-warranty service RMA numbers Appendix a Compliance information Radio and TV Interference SafetyCompliance CE Declaration of Conformity Isdn compliance Appendix B Speciﬁcations Voice processing signalling dependent Voice connectivityData connectivity Voice signalling Fax and modem supportVoice routing-session router System IP servicesManagement Physical Identiﬁcation of the SmartNode devices via Snmp SmartNode Model SysObjectID Appendix C Cabling Connecting a serial terminal Console Typical Ethernet straight-through cable diagram Ethernet Isdn BRI Appendix D Port pin-outs Console port Isdn BRI 0/0 NT/Net or TE/User port Isdn BRI 0/1 . /3 TE/Usr or NT/Net Appendix E SmartNode 4630 factory conﬁguration Introduction Appendix F End user license agreement End User License Agreement Termination Other licenses