Manuals / Paxar / Computer Equipment / Printer

Paxar 9856 manual Troubleshooting

Models: 9856

1 51

Download 51 pages 6.08 Kb

Page 47

751Printer did not sense a black mark when expected. For errors

751-753, Check the supply tracking, supply marks, black mark sensor position, and supply roll for binding. Press CANCEL and try to continue printing. Change supply.

752Printer sensed a mark in the wrong place.

753Printer sensed a mark that is too long.

754Check for a ribbon jam or remove any slack by turning the take- up reel clockwise.

755Printhead is open. Close the printhead before continuing.

756Load supplies.

757Load supplies (supply length mismatch),, because the calibrated supply length differs by plus or minus .25 inches from the format. Press FEED.

758Either the supply is not seen or the on-demand sensor is broken. Check for a label jam, clear the supply path, or reload supplies. This error may occur if you remove a label too quickly in on- demand mode. The printer does not recalibrate after this error.

763Waiting to dispense label. Press FEED.

765Printhead failure. Order a new printhead.

768Printhead has more than 10 bad dots or is not connected. Connect the printhead.

791The printer has an error pending. Turn off the printer. Wait 15 seconds and turn it back on. Resend the packets.

Troubleshooting 9-3

Image 47

Paxar 9856 manual Troubleshooting

Contents

Monarch Printer Canadian D.O.C. Warning B L E O F C O N T E N T S Specifications D i e n c e T T I N G S T a R T E DT a b l i s h i n g C o m m u n i c a t i o n s N n e c t i n g t h e P o w e r C a b l eI n g t h e C o n t r o l P a n e l T t o n s a n d L i g h t s I n g t h e M a i n M e n u I n g t h e K e y p a dMain Menu L e c t i n g a F u n c t i o nSupply SetupI t i n g a n O p t i o n Getting Started A d i n g N o n P e e l a n d F a n F o l d S u p p l y A D I N G S U P P L I E SLoading Supplies A d i n g a R i b b o n M o v i n g a R i b b o n Tear Bar Installation Thumbscrew Retainer T T I N G S U P P L Y O P T I O N S Ribbon B b o nT c h S e p a r a t o r s Supply Type E d M o d eSeparators I n t P o s i t i o n P p l y P o s i t i o n Print too far to the left Print too far to the right R g i n P o s i t i o nP p l y T y p e T P o s i t i o nSpeed E e dM M U N I C AT I O N V a L U E S User Comm U d R a t eR d L e n g t h Baud RateParity O p B i t sR i t y StopbitsFlow Control S e t t o D e Fault V a l u e sO w C o n t r o l T T I N G C O N T R a S T Setup r Press E. Press L or R until you see USA T T I N G D E Fault SCountry Currency Description N e t a r y S i g nMonetary Sign DefaultsC o n d a r y S i g n Decimal Places C i m a l P l a c e sA s h e d Z e r o Secondary SignSlashed Zero Power UPW e r U p M o d e Prompt SET O m p t S e tE a n i n g t h e P r i n t h e a d R E a N D M a I N T E N a N C EJ u s t i n g t h e S u p p l y S e n s o r J u s t i n g t h e S u p p l y W i d t h Care and Maintenance E c k i n g t h e S o f t w a r e V e r s i o n DiagnosticsA G N O S T I C S C t o r y S e t P a s s w o r dUser Diag I n t i n g T e s t L a b e l sR v i c e D i a g n o s t i c s Problem Description/Action TroubleshootingError Description/Action M m o n Error sTroubleshooting Troubleshooting I n t e r E C I F I C AT I O N SRibbon Widths