Enabled | Perle Systems 1700 instruction

Applications

1 b) Defining this remote site profile within the IP Address connect table, which will cause a call to be made when a packet for this IP address is routed,

Location: Main

ªConfiguration

ªWAN Set up

ªIP Address Connect

ªIP Address Connect Enabled

1c) Defining the Auto-Call option within the Edit Remote Site menu of this remote site profile. (The Auto-Call option causes the router to attempt to establish a connection to this remote site profile each time the router starts up.)

Location: Main

ªConfiguration

ªWAN Set up

ªRemote Site Set-up

ªEdit Remote Site

ªConnection Set-up

ªAuto call

Enabled

1 d) Setting up an activation schedule with times the connection is to be activated and deactivated

Location: Main

ªConfiguration

ªWAN Set up

ªRemote Site Set-up

ªEdit Remote Site

ªActivation

ªSchedule Activation intervals

1e) If a second ISDN channel is available and traffic level is enabled, setting the traffic load at which the second channel is to be activated.

Location: Main

ªConfiguration

ªWAN Set up

ªRemote Site Set-up

ªEdit Remote Site

ªActivation

ªThreshold

Up Threshold

Down Threshold

Up Stability timer

Down Stability timer

40

Image 46

Perle Systems 1700 manual Enabled

Contents

Bridge / Routers User And System Administration Guide Federal Communications Commission FCC Using This Manual Contents Introduction to Filtering Appendix D Interface Pinouts Unpack the Router Select a Site Identify the Reset Switch Location of the Reset Hole on Router P1705 Identify the ConnectorsP1730 Connect to the Console Make the Link Connections Power Up the Bridge/Router Managing the P1705 & P1730 Using the Menus Conventions Option Name Login to Bridge/Router and Enter the Required Configuration Password T1 or E1 56/64 kbps Number of channels As specifedFirst channel Reserved Mandatory Configuration Isdn U Isdn S/T PPP Isdn Identify the Status LEDs Off Typical Applications & How to Configure Them Bridging and Routing Should You Bridge or Route? Bridging Networks Bridged across a WAN link IP Routing IP Address / Size of Subnet Mask IP Addressing Masks IP Subnets Defining an IP Subnet Mask IP Default Gateway IP Static Route IPX Routing Novell Servers in Both Locations Novell Servers in One Location Only IPX Routed Local Area Networks Servers on one side RAW 802.3 Frames IPX RoutingEthernet-II Frames Ieee 802.2 Frames IPX Forwarding Novell Server with Dual LANsSelect LAN1 or LAN2 Numbered Links PPP Link ConfigurationPPP Overview Link IP address Unnumbered Links Peer IP address Multilink Operation Basic WAN Configurations Basic Isdn Connections Directory Number Switch TypeSpid Soft Reset Console after a full reset PPP Isdn Manual Call Quick Connections Manual Call IP Address / Subnet mask size Basic Frame Relay Configuration Frame Relay configuration Auto Learning the Frame Relay Configuration Link Speed Manual Configuration LMI Type LMI Type Quick Start Frame Relay PPP EnabledIP Address / mask size Basic Leased Line Configuration Quick Start PPP Leased Line Connections Bridge Connection Configure Remote Site Profiles Configure Remote Site Profiles for Isdn PPP Isdn Number Enabled Remote Site Alias Configure Remote Site Profile for Frame RelayªConfiguration WAN Set up Remote Site Set-up Dlci Primary Link CIR Disabled EIR Configure Remote Site Profiles for Leased Line PPP Site profile Recovery Schedule ªenabled Configure Remote Site Profiles for PPPoELAN ªTCP mss value ª1452 ªISP provided username ªPPPoE remote site alias ªServer Advanced FeaturesConfigure Dynamic Host Configuration Protocol ªIP Address / number of addresses IP address local DNS server IP address external DNS server Enter the private network IP address of each service offered Network Address Translation and Port Translation 11 Napt Configuration Security Configure PPP SecuritySecurity Level Outgoing PAP Password Incoming PAP PasswordIncoming Chap Secret Outgoing Chap Secret Configure Firewall 13 Sample Firewall Application ID# 1 for ISP remote site Enter ID# 1 for ISP remote siteInbound FTP Server Source Address Filter ID # Destination AddressDestination Mask Source Mask Network Address Translation CompressionFilters Enable Bandwidth On Demand QOS Priority Queuing Location Main ªPriority ªPriority List Number ªenable Simple Network Time Protocol Sntp ªIP Address ªTime Introduction to Filtering MAC Address Filtering Pattern Filtering Not Bridge NetBIOS &NetBEUI Windows For WorkgroupsPopular Filters IP & Related Traffic Banyan NetBIOS over TCPIP Router Other interesting TCP Ports Appendix a Menu Trees Menu Tree Menu Tree Appendix B Octet Locations on Ethernet Frames Octet Locations on a Bridged TCP/IP Frame Configuration Pages Octet Locations Octet Locations on a Bridged XNS Frame Appendix C Servicing Information Opening the case Identifying the Internal Components Changing LAN or WAN Interfaces To Clear a Lost PasswordSelecting MDI or MDI-X LAN Interface Installing the Isdn Link Modules Processor settings for the Isdn Link Modules Connecting to the ISDN-U Link Module Changing the Termination Straps on the Isdn S/T Interface Performing a Software Upgrade PC used for Tftp transfers Router a Router B Router C Link Clocking Information Pinout InformationATL-CSU/DSU Link Module Information Switches Console Pinouts DB25 Female DCE 24 & RS232C Link Pinouts DB25 Female DTE 11/X.21 Link Pinouts DB15 Female DTE RS442 & RS530 Link Pinouts DB25 Female DTE Link Pinouts DCE RS232 Null-Modem Cable Configuration Figure D-9 RS232 Null-Modem Cable Null-Modem Cable Configuration Figure D 10 V-35 Null-Modem Cable RS530 Null-Modem Cable Configuration Figure D-11 RS530 Null-Modem Cable RS530 To RS449 Conversion Cable Figure D-12 RS530 to RS449 Conversion Cable 11/X.21 Null-Modem Cable Configuration Figure D-13 V.11/X.21 Null-Modem Cable