Philips CCZ256AT owner manual Specifications, Glossary

CCZ256comb.QX33 4/6/99 9:14 PM Page 57

Specifications

General

CRT: 25-inch in line gun

Television system: NTSC-M

Closed caption system: Section 15.119, FCC (Federal Communications Commission) Standard

Video Heads: Four heads

Tape width: 1/2 inch (12.65 mm) Tape speed

SP: 33.35 mm/sec.

LP: 16.67 mm/sec.

SLP: 11.12 mm/sec.

Operating Temperature: 41˚F (5˚C) to 104˚F (40˚C)

Relative Humidity: 10% to 75%

Power requirement: AC 120V, 60Hz

Power consumption: 125W

Sound output: 1W+1W Dimensions:

24-1/2" (H) x 25-1/32" (W) x 20-3/32" (D)

622.5mm x 636 mm x 510 mm Weight: 70.4 lbs (32 kg)

Tuner Broadcast Channels

VHF 2-13, UHF 14-69

Cable TV Channels

2 – 13

Midband: A – 1

Superband: J – W

Hyperband: A-5 – A-1

Special Channel: 5A

Ultraband: 37 – 94, 100 – 125

Terminals

Antenna IN: VHF/UHF 75 ohms unbalanced

Video IN: RCA connector

Audio IN: RCA connector

Electrical Specifications

Video input level: 0.5~2.0Vp-p

Audio input level: -10dBv

Video S/N ratio

SP: More than 42dBµ

Audio S/N ratio

SP: More than 38dB

Designs and specifications are subject to change without notice and without our legal obligation.

Specifications / Glossary 57

Glossary

AUDIO IN Jacks: jacks located on the back of the TV/VCR which are used to record audio from another source.

Automatic Channel Setup: process in which the TV/VCR scans all available channels and places the ones you receive in its memory. Then, when you push the CH(annel). Up/Down buttons, you only scan through channels you receive.

Bands: settings that allow you to tune channels.

•Antenna – VHF (very high frequency; channels 2

-13) and UHF (ultra high frequency; channels 14

-69).

•Cable – all standard channels can be received without a Cable Box.

Brightness: adjusting increases or decreases the brightness of the color on-screen.

Color: adjusting pales or brightens the TV/VCR color.

Dubbing: copying a tape using a VCR.

HQ: high quality; a feature in the TV/VCR circuitry which provides enhanced picture detail.

Line Input: The channel to which you set your TV/VCR during dubbing. The line input channel is always channel 00 (A/V IN). To exit line input mode, press the CH(annel). Up/Down buttons or the Number buttons to select another channel.

Mode: a TV/VCR operation.

OTR: One-Touch Recording; programming a timed recording that starts immediately and records for 30 minutes to eight hours, whichever you specify.

Picture: adjust to increase or decrease the con- trast of the picture on-screen.

Sharpness: adjusting softens or clarifies the picture on the TV screen.

Tape Speeds: how fast the tape travels during playback or recording.

•SP (standard play) – fastest tape speed (record- ing time for a T120 tape is approximately two hours); best picture quality.

•LP (long play) – average tape speed (recording time for a T120 tape is approximately four hours).

•SLP (super long play) – slowest tape speed (recording time for a T120 tape is approximately six hours).

Tint: adjusting changes the tints of the picture on the TV/VCR from purple to green.

VCR: video cassette recorder.

VIDEO IN Jack: jack located on the back of the TV/VCR which is used to record video from anoth- er source.