Timer Recording cont’d | Philips VRX342AT specs

Timer Recording (cont’d) 33

4

Use the Number buttons (1 - 8) to select a slot in which to store the timer recording. There are eight timer recording slots. Open slots will flash on-screen.

NOTE: If you enter a number for a slot that has already been used to store a timer recording, PREVIOUSLY SET PROGRAM will appear on- screen for a few seconds. Then information about the program in that position will be displayed on-screen. If this happens, press the STA- TUS/EXIT button twice. Then start again at step 1.

5

Enter the channel you want to record.

●If you have a basic antenna or cable hookup (as shown on pages six-seven) enter the channel of the TV program you want to record. (You must enter a 0 before all single digit channels.)

●If you are recording from line input, press 0, 0. AV REAR will appear on-screen.

●If you are using a Cable Box, enter the Cable Box output chan- nel (channel 03 or 04). See page eight for details.

ONE TIME PROGRAM

PROGRAM	1
CHANNEL	– –

4-7

		VCR	TV	CABLE
	POWER	VCR	TV	/DSS
	POWER			/DSS
		2	3	VCR/TV
	1	2	3
	4	5	6
				CHANNEL
	7	8	9
	VCR PLUS+
	/ENTER

0+100

SPEED

TIME SEARCH

MUTE

VOLUME

	PLAY
– REW			F.FWD +
	STOP
REC/OTR	MEMORY	SLOW	PAUSE/STILL
MENU	STATUS/EXIT	CLEAR	EJECT

TO CORRECT PUSH CLEAR

TO END PUSH EXIT

6

Press two Number buttons for the hour(s) you want the recording to begin. Press two Number buttons for the minute(s) you want the recording to begin. Press 1 for AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.

ONE TIME PROGRAM

PROGRAM	1
CHANNEL	10
TIME ON	– – : – –

TO CORRECT PUSH CLEAR

TO END PUSH EXIT

7

Enter the recording’s stop time.

Follow the instructions in step 6 to set the recording’s stop time (AM or PM will be set automatically).

ONE TIME PROGRAM

PROGRAM	1
CHANNEL	10
TIME ON	09:30 PM
TIME OFF	– – : – –

TO CORRECT PUSH CLEAR

TO END PUSH EXIT

Instructions continue on page 34.

Helpful Hint

•Entries that do not match the VCR’s internal clock or calendar will cause a question mark (?) to appear on- screen.

Image 33

Philips VRX342AT warranty Timer Recording cont’d, Enter the recording’s stop time

Contents

VRX342AT For Customer Use Dear Philips Magnavox product owner Safety Precautions FeaturesIntroduction Use Table of Contents Using the Remote Control Putting Batteries in the Remote ControlVCR maintenance Remove the battery compartment lid on the bottom Disconnect the antenna or cable from your TV Hookups Without a Cable Box Plug in the TV and the VCR Hookups Without a Cable Box cont’d Hookups With a Cable Box Timer RecordingsRecording/Viewing Any Channel Watching TV With the VCR Off Recording One Channel/Watching Another Hookups With a Cable Box cont’dPlaying a Tape Press the Play button to play the tape Hookups With a Stereo TV 1Turn on the TV Turning on Your VCR Channel Memory Press the Number 3 button to select Tuner SET UPProgramming Channels Press the VCR button Adding/Deleting Channels Reviewing Programmed ChannelsUse the Number buttons to enter the channel number Manual Clock Setting Setting the ClockPress the Number 4 button to select SET Clock Press the Number 2 button to select SET Manual Clock Setting the Clock cont’d Automatic Clock Setting Setting the Clock cont’dPress the VCR button, then press the Menu button to Bring up the main menu display Press the Number 4 button to select SET Time Zone Time Zone Daylight-Saving Time Selection Daylight-Saving Time Selection Language Selection Press the Number 2 button to select VCR SET UPLanguage Selection Press the Number 3 button to select Language Press and release the Mute button TV Code SettingWithin 30 seconds after releasing the Mute button, press Release the TV button Find the brand of your Cable Box or Satellite System on Release the CABLE/DSS buttonWithin 30 seconds after releasing the CABLE/DSS button, use Remote Control Buttons Remote Control Buttons cont’d Press the Number 2 button to select on Screen Mode On-Screen Status DisplaysTo choose the status display mode, follow the steps below VCR Display Panel Front Panel Rear Panel Read and follow the steps below to play a tape Playing Recording Press the VCR button on the remote control Press the Stop button to stop the recording Recording One Channel/Watching Another With the Tape Speed button Channels are programmedIntact and the tape is long enough to record the programs Buttons to select the channel you want to record Daily Timer RecordingRecording Menu Screen Enter the recording’s stop time Timer Recording cont’d Timer Recording cont’d Press the STATUS/EXIT button. Program WAS COMTape Speeds See page 46 for more hints Checking or Cancelling Timer Recordings Setting Up the VCR Plus+ Programming System TV Channels Cable ChannelsLocal TV Stations Call letters Press the Number 4 button to select VCR PLUS+ REF. MAP Press the VCR button, then press the Menu button Once Panel of the VCR. If it does not, press the VCR/TV button Timer Recording With the VCR Plus+ Programming System cont’d Rerecording Tape Duplication Repeat Playback Repeat Playback Time Search Time Search Real Time Counter Memory Real Time Counter Memory Forward and Reverse Searching SP/LP/SLP Special Effects PlaybackSuper High Speed Searching LP/SLP Viewing a Still Picture Automatic Operation Features Helpful Hints Helpful Hints cont’d Cable Box Output Channel Channel 3 or Glossary Specifications Renewed Index Supplied Accessories