Time Search | Philips VRX342AT specification

42 Time Search

Time Search

Follow the steps below to program the VCR to search forward or backward a specific length of time.

1

Press the VCR button.

2

Press the TIME SEARCH button to bring up the time search display. There must be a tape in the VCR.

TIME SEARCH

0:00

3

2

1

		VCR	TV	CABLE
	POWER	VCR	TV	/DSS
	POWER			/DSS
		2	3	VCR/TV
	1	2	3
	4	5	6
				CHANNEL
	7	8	9
	VCR PLUS+
	/ENTER

0+100

SPEED

TIME SEARCH

MUTE

VOLUME

ENTER SEARCH TIME

3

Within 10 seconds, use the Number buttons to enter the desired length of time you want to skip forward or back- ward. For example, for 1 hour, 25 minutes, press Number but- tons 1, 2, 5. Or, for five minutes, press Number buttons 0, 0, 5. (Make an entry within 10 seconds of pressing the TIME SEARCH button. Otherwise, the VCR will exit Time Search mode.)

4

Within 10 seconds, press the F.FWD button or the REW(ind) button to skip forward or backward. The VCR will skip over the specified length of time, then begin playback. (The time counts down on-screen as the searching progresses.)

		PLAY
–	REW			F.FWD +
4		STOP
	REC/OTR	MEMORY	SLOW	PAUSE/STILL
	MENU	STATUS/EXIT	CLEAR	EJECT

Helpful Hints

•If you want to search for more than 59 minutes, you must enter the length of time in hours and minutes. For example, to search forward 70 minutes, press 1,1,0 at step 3.

•You can not enter the TIME SEARCH menu when you are in Recording mode.

•You can remove the Time Search display by pressing the TIME SEARCH button again.

•To cancel the Time Search when the VCR is fast forwarding or rewinding, press the STOP button once or the

TIME SEARCH button twice.

Image 42

Philips VRX342AT warranty Time Search

Contents

VRX342AT Dear Philips Magnavox product owner For Customer Use Introduction FeaturesSafety Precautions Use Table of Contents VCR maintenance Putting Batteries in the Remote ControlUsing the Remote Control Remove the battery compartment lid on the bottom Hookups Without a Cable Box Disconnect the antenna or cable from your TV Hookups Without a Cable Box cont’d Plug in the TV and the VCR Recording/Viewing Any Channel Timer RecordingsHookups With a Cable Box Watching TV With the VCR Off Playing a Tape Hookups With a Cable Box cont’dRecording One Channel/Watching Another Press the Play button to play the tape Hookups With a Stereo TV Turning on Your VCR 1Turn on the TV Programming Channels Press the Number 3 button to select Tuner SET UPChannel Memory Press the VCR button Adding/Deleting Channels Reviewing Programmed ChannelsUse the Number buttons to enter the channel number Press the Number 4 button to select SET Clock Setting the ClockManual Clock Setting Press the Number 2 button to select SET Manual Clock Setting the Clock cont’d Press the VCR button, then press the Menu button to Setting the Clock cont’dAutomatic Clock Setting Bring up the main menu display Time Zone Press the Number 4 button to select SET Time Zone Daylight-Saving Time Selection Daylight-Saving Time Selection Language Selection Press the Number 2 button to select VCR SET UPLanguage Selection Press the Number 3 button to select Language Within 30 seconds after releasing the Mute button, press TV Code SettingPress and release the Mute button Release the TV button Find the brand of your Cable Box or Satellite System on Release the CABLE/DSS buttonWithin 30 seconds after releasing the CABLE/DSS button, use Remote Control Buttons Remote Control Buttons cont’d Press the Number 2 button to select on Screen Mode On-Screen Status DisplaysTo choose the status display mode, follow the steps below VCR Display Panel Front Panel Rear Panel Playing Read and follow the steps below to play a tape Press the VCR button on the remote control Recording Recording One Channel/Watching Another Press the Stop button to stop the recording Intact and the tape is long enough to record the programs Channels are programmedWith the Tape Speed button Buttons to select the channel you want to record Recording Menu Timer RecordingDaily Screen Timer Recording cont’d Enter the recording’s stop time Timer Recording cont’d Press the STATUS/EXIT button. Program WAS COMTape Speeds Checking or Cancelling Timer Recordings See page 46 for more hints Setting Up the VCR Plus+ Programming System TV Channels Cable ChannelsLocal TV Stations Call letters Press the VCR button, then press the Menu button Press the Number 4 button to select VCR PLUS+ REF. MAP Panel of the VCR. If it does not, press the VCR/TV button Once Timer Recording With the VCR Plus+ Programming System cont’d Rerecording Tape Duplication Repeat Playback Repeat Playback Time Search Time Search Real Time Counter Memory Real Time Counter Memory Super High Speed Searching LP/SLP Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Viewing a Still Picture Automatic Operation Features Helpful Hints Helpful Hints cont’d Glossary Cable Box Output Channel Channel 3 or Specifications Renewed Index Supplied Accessories