Pioneer PDP-42MVE1 manual Option1 Settings Menu, Setting the on-screen display

Option1 Settings Menu

Setting the on-screen display

This sets the position of the menu, the display format (horizontal or vertical) etc.

Example: Turning the DISPLAY OSD off

On “OPTION1” menu, select “OSD”, then press the MENU/ SET button.

The “OSD” menu appears.

On “DISPLAY OSD” of “OSD” menu, select “OFF”.

	OSD
DISPLAY OSD		:	OFF
OSD ADJUST		:	1
OSD ANGLE		:	H
OSD ORBITER		:	OFF
OSD CONTRAST		:	LOW
SEL.	ADJ.	EXIT RETURN

Information

DISPLAY OSD settings

ON: The informations on screen size, volume control, etc. will be shown.

OFF: The informations on screen size, volume control, etc. will not be shown.

The DISPLAY button on the remote control will not function either.

OSD ADJUST settings

Adjusts the position of the menu when it appears on the screen.

The position can be set between 1 to 6.

OSD ANGLE settings

Sets the display format (landscape “H” or portrait “V”). When the unit is installed vertically set the OSD ANGLE at “V”.

“H”“V”

	OPTION1		1 / 3		OPTION1
OSD				OSD
BNC INPUT		:	RGB
D-SUB INPUT		:	RGB	BNC INPUT
RGB SELECT		:	AUTO	:		RGB
HD SELECT		:	1080B	D-SUB INPUT
INPUT SKIP		:	OFF	:		RGB
ALL RESET		:	OFF	RGB SELECT
NEXT PAGE				:		AUTO
SEL.	MENU OK	EXIT RETURN		HD SELECT
				:		1080B
				INPUT SKIP
				:		OFF
				ALL RESET
				:		OFF
						1024	768
				SEL. MENU OK
						EXIT RETURN

OSD ORBITER settings

ON: The position of the menu will be shifted by eight dots each time OSD is displayed.

OFF: OSD will be displayed at the same position.

OSD CONTRAST settings NORMAL: OSD brightness is set to normal. LOW: OSD brightness is set to lower.

Setting the PC2/COMPONENT2 connectors

Select whether to set the PC2/COMPONENT2 to RGB, component or SCART1, 2.

Example: Set the BNC INPUT mode to “COMP.”

On “BNC INPUT” of “OPTION1” menu, select “COMP.”.

	OPTION1		1 / 3
OSD
BNC INPUT		:	COMP.
D-SUB INPUT		:	RGB
RGB SELECT		:	AUTO
HD SELECT		:	1080B
INPUT SKIP		:	OFF
ALL RESET		:	OFF
NEXT PAGE
SEL.	ADJ.	EXIT RETURN

Information

BNC INPUT Settings

RGB: Use the 5BNC terminals for HD, VD and RGB signals.

COMPONENT: Use the 3BNC terminals for component signals.

SCART1: Use the 4BNC terminals for RGB with composite sync. See page 6.

SCART2: Use the 3BNC terminals for RGB and the VIDEO1 terminal for composite sync. See page 6.

Setting the PC1 connector

Select one of the signals being transmitted to the PC1 terminal.

Example: Set the D-SUB INPUT mode to “SCART3”

On “D-SUB INPUT” of “OPTION1” menu, select “SCART3”.

	OPTION1		1 / 3
OSD
BNC INPUT		:	RGB
D-SUB INPUT		:	SCART3
RGB SELECT		:	AUTO
HD SELECT		:	1080B
INPUT SKIP		:	OFF
ALL RESET		:	OFF
NEXT PAGE
SEL.	ADJ.	EXIT RETURN

Information

D-SUB INPUT Settings

RGB: Use the D-SUB terminal for RGB signals.

SCART3: Use the D-SUB terminal for RGB signal fed from SCART. See page 6.

English

OSD (On Screen Display) Controls

17

En