Pioneer PDP-42MVE1 Enabling/disabling remote control wireless transmission, Loop Out setting

English

OSD (On Screen Display) Controls

24

Enabling/disabling remote control wireless transmission

This function enables/disables remote control wireless transmission.

Example: Setting “OFF”

Set “ADVANCED OSD” to “ON” in the main menu (1/ 2), then perform the following operations.

On “IR REMOTE” of “OPTION3” menu, select “OFF”, then press the MENU/SET button.

	OPTION3		3 / 3
PREVIOUS PAGE
TIMER
PWR. ON MODE		:	LAST
KEY LOCK		:	OFF
IR REMOTE		:	OFF
LOOP OUT		:	OFF
ID NUMBER		:	ALL
VIDEO WALL
SEL.	ADJ.	EXIT RETURN

Information

IR REMOTE settings

ON: Enables remote control wireless transmission.

OFF: Disables remote control wireless transmission. Set “OFF” to avoid unwanted control from other remote controls.

Loop Out setting

When this feature is set to ON, the received signal will be looped out.

Example: Setting “ON”

Set “ADVANCED OSD” to “ON” in the main menu (1/ 2), then perform the following operations.

On “LOOP OUT” of “OPTION3” menu, select “ON”.

	OPTION3		3 / 3
PREVIOUS PAGE
TIMER
PWR. ON MODE		:	LAST
KEY LOCK		:	OFF
IR REMOTE		:	ON
LOOP OUT		:	ON
ID NUMBER		:	ALL
VIDEO WALL
SEL.	ADJ.	EXIT RETURN

Information

LOOP OUT settings

ON: The received signal will be looped out via PC1 terminal or VIDEO1 terminal.

OFF: The received signal will not loop out.

*Even if LOOP OUT is ON, signals won’t be sent out if POWER is being turned off.

To connect another display...

See page 3.

If the PC1 signal is present at the time the power switched on...

The PC1 input will be displayed regardless of the setting of LOOP OUT.

ID number setting

When using more than one of these displays, this function sets ID numbers so that operation of the remote control does not cause multiple monitors to operate at the same time.

Example: Setting “2”

Set “ADVANCED OSD” to “ON” in the main menu (1/ 2), then perform the following operations.

On “ID NUMBER” of “OPTION3” menu, select “2”.

	OPTION3		3 / 3
PREVIOUS PAGE
TIMER
PWR. ON MODE		:	LAST
KEY LOCK		:	OFF
IR REMOTE		:	ON
LOOP OUT		:	OFF
ID NUMBER		:	2
VIDEO WALL
SEL.	ADJ.	EXIT RETURN

*To reset back to ALL Press the CLEAR button.

Information

ID NUMBER settings

ALL: ID NUMBER will not be set.

1 to 256: ID NUMBER will be set.

When the ID NUMBER have been set

You can also set ID NUMBER for each remote control to operate the plasma display individually. To do so, see below.

To set the ID number for the remote control

Example: Setting “2”

Press the ID NO. SET button on the remote control. The “ID NO. SET” screen appears.

On “ID NUMBER” of “ID NO. SET” menu, select “2”.

ID NO.SET

	POSITION :	1
		: 2
ID NUMBER
	ADJ.	EXIT RETURN

*To reset back to ALL Press the CLEAR button.

Video Wall setting

Use this feature to configure a 4-25 video wall.

Set “ADVANCED OSD” to “ON” in the main menu (1/ 2), then perform the following operations.

On “OPTION3” menu, select “VIDEO WALL”, then press the MENU/SET button.

The “VIDEO WALL” screen appears.

	VIDEO WALL
DIVIDER		:	1
POSITION
DISP. MODE		:	NORMAL
AUTO ID		:	OFF
SCREEN
P. ON DELAY		:	OFF
ABL LINK		:	OFF
REPEAT TIMER		:	OFF
SEL.	ADJ.	EXIT RETURN

Note: A contingency method of shutting off the electric power should be used in cases of emergency during video wall setup.

En