System Settings

Settings after connections

After components have been connected to INPUT1 or INPUT2, on-screen setup is necessary.

Follow the procedure described below and make settings as they apply to the type of components connected.

[SIGNAL FORMAT] setup

Note

These settings are required only when using the following input signal refresh rates: 1 31.5 kHz horizontal / 60 Hz vertical; 2

48.4kHz horizontal / 60 Hz vertical, or 56.1 kHz horizontal / 70 Hz vertical; 3 64 kHz horizontal / 60 Hz vertical, 80 kHz horizontal / 75 Hz vertical, or 91.2 kHz horizontal / 85 Hz vertical. No manual setup is necessary for signals with other refresh rates, since adjustments are performed automatically (the [SIGNAL FORMAT] item will not be displayed).

3Use the 5/∞ buttons to select [SIGNAL FORMAT], then press the SET button.

 

MENU

 

 

INPUT1

 

PICTURE SCREEN

SETUP

 

OPTION

 

 

POWER MANAGEMENT : OFF

 

 

 

CLAMP POSITION

: AUTO

 

 

 

SIGNAL FORMAT

: V G A

 

 

 

 

 

 

 

 

4Use the 2/3 buttons to select the display mode.

SIGNAL FORMAT :

VGA

SET SET

MENU EXIT

1When the input signal has a refresh rate of 31.5 kHz horizontal / 60 Hz vertical, pressing 2/3 will cause the display mode to change alternately as follows:

3VGA 2 3 WVGA 2

English

MENU

5/∞

2/3

MENU

2/3

SET

SET

5/∞

Main unit operating

Remote control unit

panel

 

1Press the MENU button to display the menu screen.

MENU

 

 

 

 

 

 

 

 

INPUT1

PICTURE

 

SCREEN

 

 

SETUP

OPTION

 

CONTRAST

 

:

0

 

 

 

 

 

 

 

 

 

 

 

 

 

BRIGHTNESS

:

0

 

 

 

 

 

 

 

R.LEVEL

 

:

0

 

 

 

 

 

 

 

G.LEVEL

 

:

0

 

 

 

 

 

 

 

 

 

 

 

 

 

B.LEVEL

 

:

0

 

 

 

 

 

 

 

H.ENHANCE

:

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V.ENHANCE

 

:

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PICTURE RESET

 

 

 

 

 

 

 

 

 

 

 

 

 

ENTER

 

 

 

 

 

 

 

EXIT

 

SET

 

MENU

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2Use the 2/3 buttons to select [SETUP].

 

MENU

 

 

INPUT1

 

PICTURE SCREEN

SETUP

 

OPTION

 

 

POWER MANAGEMENT : OFF

 

 

 

CLAMP POSITION

: AUTO

 

 

 

SIGNAL FORMAT

: V GA

 

 

 

 

 

 

 

 

2When the input signal has a refresh rate of 48.4 kHz horizontal / 60 Hz vertical, or 56.1 kHz horizontal / 70 Hz vertical, pressing 2/3 will cause the display mode to change alternately as follows:

3 PC AUTO 2 3 XGA 2

3WXGA 2

3When the input signal has a refresh rate of 64 kHz horizontal / 60 Hz vertical, 80 kHz horizontal / 75 Hz vertical, or 91.2 kHz horizontal / 85 Hz vertical, pressing 2/3 will cause the display mode to change alternately as follows:

3SXGA 2 3 SXGA+ 2

If the [PC AUTO] setting is selected when using the above PC input signals, screen resolution will automatically switch between [XGA] and [WXGA].

Notes

÷The [PC AUTO] setting supports automatic signal selection only when using RGB separate SYNC inputs.

÷When G ON SYNC or Composite SYNC signals are input, selecting [PC AUTO] will cause the screen resolution to be set to [XGA] only.

÷When using G ON SYNC or Composite SYNC with WXGA inputs, set [SIGNAL FORMAT] manually to [WXGA].

5Press the SET button.

The setting is stored in memory and the screen returns to that shown in step 3.

6When the setup is completed, press the MENU button to exit the menu screen.

Note

Make [SIGNAL FORMAT] setting for each input (INPUT1 and INPUT2).

17

En

System Settings