PICTURE/SCREEN Adjustment

English

PICTURE/SCREEN Adjustment

Adjusting screen POSITION, CLOCK, and PHASE <automatic adjust>

By pressing the AUTO SET UP button on either remote control unit or the plasma display’s operating panel (or by selecting [AUTO SET UP MODE] from the menu), the unit will automatically set the screen position and clock to best match the current image input.

Note

This setting is supported only when INPUT1 is selected. The function is disabled when INPUT2 is selected.

When the button is pressed, the optimum settings are automatically selected for the current input source.

AUTO

SET UP

Remote control unit

AUTO SET UP

Main unit operating panel

Press the AUTO SET UP button on either the main unit or remote control unit.

When the automatic setup mode is selected, the unit will automatically be adjusted to the optimum image settings whenever the power is turned on, the input source is changed, or the type of input signal is changed.

MENU

5/

2/3

MENU

2/3

SET

SET

5/

Main unit operating

Remote control unit

panel

 

1Press the MENU button to display the menu screen.

MENU

 

 

 

 

 

 

 

 

INPUT1

PICTURE

 

SCREEN

 

 

SETUP

OPTION

 

CONTRAST

 

:

0

 

 

 

 

 

 

 

 

 

 

 

 

 

BRIGHTNESS

:

0

 

 

 

 

 

 

 

R.LEVEL

 

:

0

 

 

 

 

 

 

 

G.LEVEL

 

:

0

 

 

 

 

 

 

 

 

 

 

 

 

 

B.LEVEL

 

:

0

 

 

 

 

 

 

 

H.ENHANCE

:

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V.ENHANCE

 

:

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PICTURE RESET

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENTER

 

 

 

 

 

 

 

EXIT

 

SET

 

MENU

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2 Use the 2/3 buttons to select [OPTION].

 

 

 

 

 

MENU

 

 

 

 

INPUT1

 

 

 

 

 

PICTURE

SCREEN

SETUP

 

OPTION

 

 

 

 

 

 

LANGUAGE

 

 

: ENGLISH

 

 

 

 

 

 

ENERGY SAVE

 

 

: STANDARD

 

 

 

 

 

 

SCREEN MGT.

 

 

: OFF

 

AUTO SET UP

 

 

 

 

ORBITER

 

 

: OFF

 

 

 

 

 

 

MASK CONTROL

 

 

: ON

 

 

 

 

 

 

AUTO SET UP MODE

: INACTIVE

 

 

 

 

 

 

AUTO FUNCTION

 

 

: OFF

 

 

 

 

 

 

AUDIO OUT

 

 

: FIXED

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENTER

 

 

EXIT

 

 

 

 

 

 

SET

MENU

 

 

 

 

 

 

 

 

 

 

 

 

 

Note

Optimum settings may not be possible for low-luminance and certain other signals. In such cases, set the [AUTO SETUP MODE] to [INACTIVE], and use the manual adjustment methods explained in the following section, “Adjusting screen

POSITION, CLOCK, and PHASE <manual adjust>“.

26

En