The System Setup menu
3Select each channel in turn and adjust
the distance as necessary.
Use / to adjust the delay of the speaker you selected to match the reference speaker. The delay is measured in terms of speaker distance from 0.5 to 45.0 feet (0.1 m to 13 m).
3b.Fine | SP | Distance |
L |
| 10.0ft (Reference) |
R | [ | 9.0ft ] |
C |
| 9.5ft |
LS | [ | 6.0ft ] |
RS | [ | 6.5ft ] |
SBL | [ | 6.0ft ] |
SBR | [ | 6.5ft ] |
SW | [ 12.5ft ] | |
|
| :Finish |
Listen to the reference speaker and use it to measure the target channel. From the listening position, face the two speakers with your arms outstretched pointing at each speaker. Try to make the two tones sound as if they are arriving simultaneously at a position slightly in front of you and between your arm span.
When it sounds like the delay settings are matched up, press ENTER to confirm and continue to the next channel.
•For comparison purposes, the reference speaker will change depending on which speaker you select.
•If you want to go back and adjust a channel, simply use / to select it.
4When you’re finished, press RETURN. You return to the Manual MCACC setup menu.
Acoustic Calibration EQ
Acoustic Calibration Equalization is a kind of room equalizer for your speakers (excluding the subwoofer). It works by measuring the acoustic characteristics of your room and neutralizing the ambient characteristics that
06
can color the original source material. This |
| |||||||||||
provides a ‘flat’ equalization setting. If you’re | English | |||||||||||
not satisfied with the automatic adjustment, | ||||||||||||
| ||||||||||||
you can also adjust these settings manually to |
| |||||||||||
get a frequency balance that suits your tastes. |
| |||||||||||
|
|
|
|
|
|
|
|
| ||||
Setting the Acoustic Calibration EQ |
| |||||||||||
automatically |
|
|
|
|
|
|
| Deutsch | ||||
page 8, ALL CH ADJUST and FRONT ALIGN |
| |||||||||||
If you have already completed Automatically |
|
| ||||||||||
setting up for surround sound (MCACC) on |
|
| ||||||||||
(below) should already be set. Therefore, if you |
|
| ||||||||||
|
| |||||||||||
want to adjust your settings manually, you can |
|
| ||||||||||
| Français | |||||||||||
1 Select ‘EQ AUTO Setting’ from the |
| |||||||||||
skip to Setting the Acoustic Calibration EQ |
|
| ||||||||||
manually below. |
|
|
|
|
|
| ||||||
Manual MCACC setup menu. |
|
| ||||||||||
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
| |
| 3.Manual | MCACC |
|
|
| 3c.EQ AUTO Setting | Italiano | |||||
|
| a.Fine Ch Level |
|
|
|
|
|
|
|
| ||
|
| b.Fine SP Distance |
| Set microphone. |
| |||||||
|
| c.EQ | AUTO Setting |
|
|
| ||||||
|
| d.EQ | Data Copy |
|
|
| Turn on Subwoofar. |
| ||||
|
| e.EQ | CUSTOM1 | Adjust |
|
|
|
|
|
| ||
|
| f .EQ | CUSTOM2 | Adjust |
|
|
|
|
|
| ||
|
| g.EQ | Data Check |
|
|
|
|
|
| |||
|
|
|
| :Return |
| :Cancel |
|
|
| |||
• Make sure the microphone is connected. |
|
| Nederlands | |||||||||
|
| |||||||||||
• If you’re using a subwoofer, it is |
|
| ||||||||||
| automatically detected every time you |
|
| |||||||||
| switch on the system. Make sure it is on |
|
| |||||||||
| and the volume is at the middle position. | Español | ||||||||||
| regarding high background noise levels | |||||||||||
• See Other problems when using the Auto |
| |||||||||||
MCACC Setup on page 10 for notes and other possible interference.
2Wait for the Auto MCACC Setup to finish.
3c.EQ AUTO Setting |
|
|
| 3c.EQ AUTO Setting |
|
| |||||
Now Analyzing |
|
|
| Now | Analyzing |
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
Environment Check |
|
|
| Surround | Analyzing |
|
| ||||
Ambient Noise | [ | ] |
| Channel | Level | [ | ] | ||||
Microphone | [ | ] |
| Acoustic | Cal EQ | [ | ] | ||||
Speaker YES/NO | [ | ] |
|
|
|
|
|
|
| ||
|
|
| :Cancel |
|
|
|
|
| :Cancel | ||
As the receiver outputs test tones, the frequency balance is adjusted automatically for the following settings:
37
En
