Additional information | 12 |
Problem | Remedy |
The PHASE CONTROL feature | • If applicable, check that the lowpass filter switch on your subwoofer is off, or the |
doesn’t seem to have an | lowpass cutoff is set to the highest frequency setting. If there is a PHASE setting on |
audible effect. | your subwoofer, set it to 0º (or depending on the subwoofer, the setting where you |
| think it has the best overall effect on the sound). |
| • Make sure the speaker distance setting is correct for all speakers (see Speaker |
| Distance on page 42). |
|
|
Considerable noise in radio | • Connect the antenna (page 18) and adjust the position for best reception. |
broadcasts. | • Route any loose cables away from the antenna terminals and wires. |
| • Fully extend the FM wire antenna, position for best reception, and secure to a wall |
| (or connect an outdoor FM antenna). |
| • Connect an additional internal or external AM antenna (page 17). |
| • Turn off equipment causing interference or move it away from the receiver (or |
| move antennas farther away from equipment causing noise). |
|
|
Broadcast stations cannot be | • Connect an outdoor antenna (refer to page 17). |
selected automatically. |
|
|
|
Noise during playback of a | • Move the cassette deck away from your receiver, until the noise disappears. |
cassette deck. |
|
|
|
Sound is produced from other | • Set the SIGNAL SELECT to AUTO, DIGITAL or ANALOG according to the type of |
components, but not from LD | connections made. (refer to page 32). |
or DVD player. | • Set the digital input settings correctly (refer to page 59). |
| • Make digital connections (refer to page 12) and set the SIGNAL SELECT to |
| DIGITAL (refer to page 32). |
| • Refer to the instruction manual supplied with the DVD player. |
|
|
No sound is output or a noise | • Set the digital volume level of the player to full, or to the neutral position. |
is output when software with | • Make sure the player’s settings are correct and/or the DTS signal out is on. Refer |
DTS is played back. | to the instruction manual supplied with the DVD player. |
| • Set the input signal type to DIGITAL (see Choosing the input signal on page 32) |
|
|
During a playback search, | • This is not a malfunction, but be sure to turn the volume down to prevent the |
noise is output from a DTS | output of loud noise from your speakers. |
compatible CD player. |
|
|
|
Everything seems to be set up | Check that the positive/negative speaker terminals on the receiver are matched with |
correctly, but the playback | the corresponding terminals on the speakers (see Connecting the speakers on |
sound is odd. | page 18). |
|
|
There seems to be a time lag | • See Automatically setting up for surround sound (MCACC) on page 8 to set up your |
between the speakers and the | system again using MCACC (this will automatically compensate for a delay in the |
output of the subwoofer. | subwoofer output). |
|
|
After using the Auto MCACC | • |
Setup, the speaker size setting | Switch off all appliances in the room and rerun the Auto MCACC Setup. |
(LARGE or SMALL) is incorrect. |
|
|
|
Can’t operate the remote | • Replace the batteries (refer to page 6). |
control. | • Operate within 7 m (23 ft.), 30° of the remote sensor (refer to page 26). |
| • Remove the obstacle or operate from another position. |
| • Avoid exposing the remote sensor on the front panel to direct light. |
|
|
The display is dark or off. | • Press DIMMER on the control repeatedly to return to the default. |
|
|
The System Setup screen | • When the receiver is in standby, switch to BURST.OFF by holding down STEREO/ |
doesn’t appear. | F.S.SURR (front panel) and pressing STANDBY/ON (the current setting is displayed). |
|
|
English Deutsch Français Italiano Nederlands Español
63
En
