Pioneer VSX-LX52 manual Power ON Level Setup, Volume Limit Setup, Remote Control Mode Setup

11The system and the other setup

Power ON Level Setup

The volume can be set so that it is always set to the same level when the receiver’s power is turned on.

1Select ‘Power ON Level Setup’ from the Other Setup menu.

4d.Other Setup	4d4.Power ON Level Setup
A/V RECEIVER	A/V RECEIVER
1. KURO LINK Setup	Power ON Level :	LAST

2. Multi Ch In Setup

3. ZONE Audio Setup

4. Power ON Level Setup

5. Volume Limit Setup

6. Remote Control Mode Setup

7. Flicker Reduction Setup

Exit Return Exit Finish

2Select the Power ON Level setting you want.

•LAST – When the power is turned on, the volume is set to the same level as when the power was last turned off.

•“---” – When the power is turned on, the volume is set to minimum level.

•–80.0dBto +12.0dB – Specify the volume to be set when the power is turned, in steps of 0.5 dB.

It is not possible to set a volume level greater than the value specified at Volume Limit Setup.

3When you’re finished, press RETURN. You will return to the Other Setup menu.

Volume Limit Setup

Use this function to limit the maximum volume. The volume cannot be increased above the level set here, even by operating MASTER VOLUME button (or the dial on the front panel).

1Select ‘Volume Limit Setup’ from the Other Setup menu.

4d.Other Setup	4d5.Volume Limit Setup
A/V RECEIVER		A/V RECEIVER
1. KURO LINK Setup
	Volume Limit :	OFF

2. Multi Ch In Setup

3. ZONE Audio Setup

4. Power ON Level Setup

5. Volume Limit Setup

6. Remote Control Mode Setup

7. Flicker Reduction Setup

Exit Return Exit Finish

2Select the Volume Limit setting you want.

•OFF – The maximum volume is not limited.

•–20.0dB/–10.0dB/0.0dB– The maximum volume is limited to the value set here.

3When you’re finished, press RETURN.

You will return to the Other Setup menu.

Remote Control Mode Setup

• Default setting: 1

This sets this receiver’s remote control mode to prevent erroneous operation when multiple units of the receiver are being used.1

1Select ‘Remote Control Mode Setup’ from the Other Setup menu.

4d.Other Setup		4d6.Remote Control Mode Setup
A/V RECEIVER		A/V RECEIVER
1. KURO LINK Setup
		Remote Control Mode :	1
2. Multi Ch In Setup
3. ZONE Audio Setup
4. Power ON Level Setup
5. Volume Limit Setup
6. Remote Control Mode Setup
7. Flicker Reduction Setup
			OK
Exit	Return	Exit		Cancel

2Select the Remote Control Mode setting you want.

3Select “OK” to change the remote control mode.

4Follow the instructions on the screen to change the remote control’s setting.

See Operating multiple receivers on page 67.

5When you’re finished, press RETURN.

You will return to the Other Setup menu.

Flicker Reduction Setup

• Default setting: 4

The GUI screen’s resolution can be increased. If you feel the GUI screen is hard to see, try changing this setting. Note that the resolution in this setting only affects the GUI screen; it has no influence on the video output.

1Select ‘Flicker Reduction Setup’ from the Other Setup menu.

4d.Other Setup	4d7.Flicker Reduction Setup
A/V RECEIVER	A/V RECEIVER
1. KURO LINK Setup
	Flicker Reduction :	4

2.Multi Ch In Setup

3.ZONE Audio Setup

4.Power ON Level Setup

5.Volume Limit Setup

6.Remote Control Mode Setup

7.Flicker Reduction Setup

Exit Return Exit Finish

2Select the Flicker Reduction setting you want.

3When you’re finished, press RETURN.

You will return to the Other Setup menu.

Note

1 If you change this receiver’s setting, also change the setting on the remote control.

90

En