Manuals / Brands / Computer Equipment / Switch / Q-Logic / Computer Equipment / Switch

Q-Logic 5800V Heartbeat LED (Green), System Fault LED (Amber), Maintenance Button

1 134

Download 134 pages, 2.49 Mb

1–General Description

Chassis Controls and LEDs

59265-02 B 1-3

Heartbeat LED (Green)

The Heartbeat LED indicates the status of the internal switch processor and the

results of the power-on self test (POST). Following a normal power-up, the

Heartbeat LED blinks approximately once per second to indicate that the switch

passed the POST and that the internal switch processor is running. In

maintenance mode, the Heartbeat LED remains lit. Refer to “Heartbeat LED Blink

Patterns” on page 4-3 for more information about Heartbeat LED blink patterns.

System Fault LED (Amber)

The System Fault LED lights up to indicate that a fault exists in the switch

firmware or hardware. Fault conditions include POST errors, over-temperature

conditions, and power supply malfunctions. The Heartbeat LED shows a blink

code for POST errors and over temperature conditions. For more information,

refer to “Heartbeat LED Blink Patterns” on page 4-3.

Maintenance Button

The Maintenance button, shown in Figure 1-2, is a dual-function momentary

switch on the front panel. Press the maintenance button to reset the switch, or to

place the switch in maintenance mode. Maintenance mode sets the IP address to

10.0.0.1 and provides access to the switch for maintenance purposes when flash

memory or the resident configuration file has been corrupted. For more

information, see “Recovering a Switch Using Maintenance Mode” on page4-13.

Resetting a Switch

To reset the switch, use a pointed tool to press and hold the Maintenance button

for less than two seconds. The switch responds as follows:

1. All the chassis LEDs light up except the System Fault LED.

2. After approximately one minute, the POST begins, extinguishing the

Heartbeat LED.

3. When the POST is complete, the Input Power LED lights up, and the

Heartbeat LED flashes once per second.

Placing the Switch in Maintenance Mode

To place the switch in maintenance mode:

1. Isolate the switch from the fabric.

2. Using a pointed tool, press and hold the Maintenance button for a few

seconds until only the Heartbeat LED is lit. Hold the maintenance button

until the Heartbeat LED goes out, and then release the button. The

Heartbeat LED remains lit while the switch is in maintenance mode.

To exit maintenance mode, and return to normal operation, press the

Maintenance button momentarily.

Contents

Main Document Revision History Table of Contents Preface 1 General Description 2 Planning 3 Installation 4 Diagnostics/Troubleshooting 5 Removal/Replacement A Specifications Glossary Index List of Figures List of Tables Preface Intended Audience Related Materials Whats New in this Release Safety Notices Sicherheitshinweise Notes informatives relatives la scurit Advertencias de seguridad Communications Statements Federal Communications Commission (FCC) Class A Statement Canadian Department of Communications Class A Compliance Statement Avis de conformit aux normes du ministre des Communications du Canada CE Statement VCCI Class A Statement Laser Safety Information Electrostatic Discharge Sensitivity (ESDS) Precautions Accessible Parts Pices Accessibles Zugngliche Teile General Public License Preamble Terms and Conditions for Copying, Distribution and Modification Page Page Page How to Apply These Terms to Your New Programs Page qfsApp Program License Technical Support Training Contact Information Page Page 1 Figure 1-1. QLogic 5802V Stackable Fibre Channel Switch Chassis Controls and LEDs Figure 1-2. Chassis LEDs and Controls Input Power LED (Green) Heartbeat LED (Green) System Fault LED (Amber) Maintenance Button Resetting a Switch Placing the Switch in Maintenance Mode Fibre Channel Ports Figure 1-3. Fibre Channel Ports Port LEDs Figure 1-4. Port LEDs Port Logged-In LED (Green) Port Activity LED (Green) Transceivers Port Types Table 1-1. Fibre Channel Port Types Ethernet Port Figure 1-5. Ethernet Port Serial Port Figure 1-6. Serial Port and Pin Identification Table 1-2. Serial Port Pin Identification Power Supplies and Fans Model 5800V Model 5802V Figure 1-7. Model 5802V Power Supplies Switch Management QuickTools Web Applet Enterprise Fabric Suite Command Line Interface Application Programming Interface Simple Network Management Protocol Storage Management InitiativeSpecification File Transfer Protocols 2 Devices Device Access Table 2-1. Zoning Database Limits Performance Distance Table 2-2. Port Transmission Distances Bandwidth Table 2-3. Extended Credit Distances and Cable Lengths Latency Feature Licensing Table 2-4. Port-to-Port Latency Multiple Chassis Fabrics Optimizing Device Performance Domain ID, Principal Priority, and Domain ID Lock Stacking Figure 2-1. Two-Switch Stack Figure 2-2. Three-Switch Stack Page Figure 2-5. Six Switch Stack Common Topologies Cascade Topology Figure 2-6. Cascade-with-a-Loop Topology Mesh Topology Figure 2-7. Mesh Topology MultiStage Topology Figure 2-8. Multistage Topology Transparent Routing Page Page Switch Services Page Internet Protocol Support Security User Account Security IP Security Port Binding Connection Security Device Security Page 2Planning Security 2-22 59265-02 B Security Example: Switches and Adapters with Authentication Figure 2-9. Security Example: Switches and Adapters Page Page Security Example: RADIUS Server Figure 2-10. Security Example: RADIUS Server Page Page Page 2Planning Security 59265-02 B 2-29 Security Example: Host Authentication Figure 2-11. Security Example: Management Server Page Fabric Management Page 3 Site Requirements Fabric Management Workstation Switch Power Requirements Environmental Conditions Table 3-1. Management Workstation Requirements Installing a Switch Figure 3-1. QLogic 5802V Fibre Channel Switch Mount the Switch Install the Transceivers Page Configure the Workstation Configuring the Workstation IP Address for Ethernet Connections Windows Workstation Linux or Solaris Workstation Mac OS X Workstation Configuring the Workstation Serial Port Connect the Switch to AC Power Page Connect the Workstation to the Switch Figure 3-4. Workstation Cable Connections Configure the Switch QuickTools Switch Configuration CLI Switch Configuration Cable Devices to the Switch Installing Firmware Using QuickTools to Install Firmware Using the CLI to Install Firmware One-Step Firmware Installation Page Custom Firmware Installation Adding a Switch to an Existing Fabric Installing Feature License Keys Page 4 Chassis Diagnostics Figure 4-1. Chassis LEDs Input Power LED Is Not Lit System Fault LED Is Lit Power-On Self Test Diagnostics Heartbeat LED Blink Patterns Page Configuration File System Error Blink Pattern Figure 4-4. Configuration File System Error Blink Pattern Over-Temperature Blink Pattern Figure 4-5. Over-Temperature Blink Pattern Logged-In LED Indications Figure 4-6. Logged-In LED E_Port Isolation Page Excessive Port Errors Transceiver Diagnostics Power Supply Diagnostics Figure 4-7. Model 5802V Power Supply LEDs Recovering a Switch Using Maintenance Mode Exiting the Maintenance Menu (Option 0) Unpacking a Firmware Image File in Maintenance Mode (Option 1) Page Remaking the File System in Maintenance Mode (Option 6) Resetting the Switch in Maintenance Mode (Option 7) Updating the Boot Loader in Maintenance Mode (Option 8) 5 Transceiver Removal and Replacement Power Supply Removal and Replacement Figure 5-1. Power Supply Removal Figure 5-2. Power Supply Installation Page A Fabric Specifications Page Maintainability Fabric Management Dimensions Electrical Power Cord Specifications Table A-1. Available Power Cords Table A-1. Available Power Cords (Continued) Region/Country Specification QLogic SKU Number Environmental Regulatory Certifications Glossary Page Page Page Page Page Page Page Index Numerics A B C D E F G H I L M N Q R S T U V W X Z