Q-Logic 5800V Switch Services

2–Planning

Switch Services

2-16 59265-02 B

The name of the inter-fabric zone begins with IFZ followed by the lowest

device port WWN followed by the remaining port WWN, all uppercase,

separated by underscores (_). For example, consider the following local and

remote device WWNs:

Local device: 21:00:00:e0:8b:0e:d3:59

Remote device: 22:00:00:04:cf:a8:7f:2d

The inter-fabric zone name would be:

IFZ_210000E08B0ED359_22000004CFA87F2D

4. Apply the same inter-fabric zone that was created on the local fabric to the

active zoning on the remote fabric. The application creates a suggested list

of commands during the mapping process that, when run on a remote fabric

consisting of Brocade or Cisco switches, will make the necessary zoning

changes to the remote fabric. See the QLogic 5800V Series QuickTools

Switch Management User’s Guide or QLogic 5800V Series Enterprise

Fabric Suite User’s Guide for important details on creating and using this list

of suggested commands. When modifications to the active zoning on both

fabrics are complete, the transparent routing connection becomes active,

and the local devices will discover the remote devices.

Switch Services

You can configure your switch to suit the demands of your environment by

enabling or disabling a variety of switch services. Familiarize yourself with the

following switch services and determine which ones you need.

Telnet: Provides for the management of the switch over a Telnet connection .

Disabling this service is not recommended. The default is enabled.

Secure Shell (SSH): Provides for secure remote connections to the switch

using SSH. Your workstation must also use an SSH client. The default is

disabled.

GUI Management: Provides for out-of-band management of the switch with

Enterprise Fabric Suite, QuickTools, the API, SNMP, and SMI-S. If this

service is disabled, the switch can only be managed inband or through the

serial port. The default is enabled.

Inband Management: Provides for the management of the switch over an

inter-switch link using Enterprise Fabric Suite, QuickTools, SNMP,

management server, or the API. If you disable inband management, you can

no longer communicate with that switch by means other than an Ethernet or

serial connection.The default is enabled.

Contents

Main Document Revision History Table of Contents Preface 1 General Description 2 Planning 3 Installation 4 Diagnostics/Troubleshooting 5 Removal/Replacement A Specifications Glossary Index List of Figures List of Tables Preface Intended Audience Related Materials Whats New in this Release Safety Notices Sicherheitshinweise Notes informatives relatives la scurit Advertencias de seguridad Communications Statements Federal Communications Commission (FCC) Class A Statement Canadian Department of Communications Class A Compliance Statement Avis de conformit aux normes du ministre des Communications du Canada CE Statement VCCI Class A Statement Laser Safety Information Electrostatic Discharge Sensitivity (ESDS) Precautions Accessible Parts Pices Accessibles Zugngliche Teile General Public License Preamble Terms and Conditions for Copying, Distribution and Modification Page Page Page How to Apply These Terms to Your New Programs Page qfsApp Program License Technical Support Training Contact Information Page Page 1 Figure 1-1. QLogic 5802V Stackable Fibre Channel Switch Chassis Controls and LEDs Figure 1-2. Chassis LEDs and Controls Input Power LED (Green) Heartbeat LED (Green) System Fault LED (Amber) Maintenance Button Resetting a Switch Placing the Switch in Maintenance Mode Fibre Channel Ports Figure 1-3. Fibre Channel Ports Port LEDs Figure 1-4. Port LEDs Port Logged-In LED (Green) Port Activity LED (Green) Transceivers Port Types Table 1-1. Fibre Channel Port Types Ethernet Port Figure 1-5. Ethernet Port Serial Port Figure 1-6. Serial Port and Pin Identification Table 1-2. Serial Port Pin Identification Power Supplies and Fans Model 5800V Model 5802V Figure 1-7. Model 5802V Power Supplies Switch Management QuickTools Web Applet Enterprise Fabric Suite Command Line Interface Application Programming Interface Simple Network Management Protocol Storage Management InitiativeSpecification File Transfer Protocols 2 Devices Device Access Table 2-1. Zoning Database Limits Performance Distance Table 2-2. Port Transmission Distances Bandwidth Table 2-3. Extended Credit Distances and Cable Lengths Latency Feature Licensing Table 2-4. Port-to-Port Latency Multiple Chassis Fabrics Optimizing Device Performance Domain ID, Principal Priority, and Domain ID Lock Stacking Figure 2-1. Two-Switch Stack Figure 2-2. Three-Switch Stack Page Figure 2-5. Six Switch Stack Common Topologies Cascade Topology Figure 2-6. Cascade-with-a-Loop Topology Mesh Topology Figure 2-7. Mesh Topology MultiStage Topology Figure 2-8. Multistage Topology Transparent Routing Page Page Switch Services Page Internet Protocol Support Security User Account Security IP Security Port Binding Connection Security Device Security Page 2Planning Security 2-22 59265-02 B Security Example: Switches and Adapters with Authentication Figure 2-9. Security Example: Switches and Adapters Page Page Security Example: RADIUS Server Figure 2-10. Security Example: RADIUS Server Page Page Page 2Planning Security 59265-02 B 2-29 Security Example: Host Authentication Figure 2-11. Security Example: Management Server Page Fabric Management Page 3 Site Requirements Fabric Management Workstation Switch Power Requirements Environmental Conditions Table 3-1. Management Workstation Requirements Installing a Switch Figure 3-1. QLogic 5802V Fibre Channel Switch Mount the Switch Install the Transceivers Page Configure the Workstation Configuring the Workstation IP Address for Ethernet Connections Windows Workstation Linux or Solaris Workstation Mac OS X Workstation Configuring the Workstation Serial Port Connect the Switch to AC Power Page Connect the Workstation to the Switch Figure 3-4. Workstation Cable Connections Configure the Switch QuickTools Switch Configuration CLI Switch Configuration Cable Devices to the Switch Installing Firmware Using QuickTools to Install Firmware Using the CLI to Install Firmware One-Step Firmware Installation Page Custom Firmware Installation Adding a Switch to an Existing Fabric Installing Feature License Keys Page 4 Chassis Diagnostics Figure 4-1. Chassis LEDs Input Power LED Is Not Lit System Fault LED Is Lit Power-On Self Test Diagnostics Heartbeat LED Blink Patterns Page Configuration File System Error Blink Pattern Figure 4-4. Configuration File System Error Blink Pattern Over-Temperature Blink Pattern Figure 4-5. Over-Temperature Blink Pattern Logged-In LED Indications Figure 4-6. Logged-In LED E_Port Isolation Page Excessive Port Errors Transceiver Diagnostics Power Supply Diagnostics Figure 4-7. Model 5802V Power Supply LEDs Recovering a Switch Using Maintenance Mode Exiting the Maintenance Menu (Option 0) Unpacking a Firmware Image File in Maintenance Mode (Option 1) Page Remaking the File System in Maintenance Mode (Option 6) Resetting the Switch in Maintenance Mode (Option 7) Updating the Boot Loader in Maintenance Mode (Option 8) 5 Transceiver Removal and Replacement Power Supply Removal and Replacement Figure 5-1. Power Supply Removal Figure 5-2. Power Supply Installation Page A Fabric Specifications Page Maintainability Fabric Management Dimensions Electrical Power Cord Specifications Table A-1. Available Power Cords Table A-1. Available Power Cords (Continued) Region/Country Specification QLogic SKU Number Environmental Regulatory Certifications Glossary Page Page Page Page Page Page Page Index Numerics A B C D E F G H I L M N Q R S T U V W X Z