Chimney Height / Rise and Run | Radware VOYA-GRAND-MBK specs

VOYAGEUR GRAND Wood Insert

R

J. Ovalizing Round Stainless Steel Liners

Ovalizing round stainless steel liners to accommodate the liner passing through the damper region of a fireplace is an allowable and acceptable practice.

Ensure that the ovalization is minimized to the extent required to fit through the damper.

K. Chimney Height / Rise and Run

To be sure that your Quadra-Fire insert burns properly, the chimney draft (static pressure) should be approximately -0.10 inches water column (W.C.) during a high burn and -0.04 inches W.C. during a low burn, measured 6 inches (152mm) above the top of the insert after one hour of operation at each burn setting.

NOTE: These are guidelines only, and may vary somewhat for individual installations.

•This product was designed for and tested on a 6 inch

(152mm) chimney, 14 to 16 feet (4.27-4.87m) high, (in- cludes appliance height) measured from the base of the appliance.

•The further your stack height or diameter varies from this configuration, the possibility of performance problems ex- ists.

•Chimney height may need to be increased by 2 - 3% per each 1000 feet (304.8m) above sea level.

•It is not recommended to use offsets or elbows at altitudes above 4000 feet (1219.2m) above sea level or when there are other factors that affect flue draft.

WARNING

Fire Risk.

Do NOT pack insulation or other combustibles between spacers.

•ALWAYS maintain specified clearances around venting and spacers.

•Install spacers as specified.

Failure to keep insulation or other material away from vent pipe may cause fire.

WARNING

Fire Risk.

Failure to install a full reline may cause:

•Creosote accumulation creating increased risk of chimney fire.

•Lose protection to combustible surfaces from the liner in case of fire.

•Poor performance and start-ups.

•Less access to chimney for required maintenance.

WARNING

Fire Risk.

This appliance relies upon natural draft to operate properly.

•Chimney heights exceeding 25 feet (7.62m) from base of appliance may create an over-draft situation.

•Overdraft condition may create over-firing.

Over-firing may ignite creosote and/or damage appli- ance and chimney.

Page 38

7075-166

September 25, 2012

Image 38

Radware VOYA-GRAND-MBK, VOYA-GRAND-PMH owner manual Chimney Height / Rise and Run

Contents

Voyageur Grand Wood Insert Hot glass will cause burns Voyageur Grand Wood Insert Welcome to the Quadra-Fire Family Table of Contents Limited Lifetime Warranty Warranty Conditions Listing and Code Approvals BTU & Efficiency SpecificationsGlass Specifications Appliance Certification General Operating Parts Operating InstructionsYour Wood Appliance Overfiring Voyageur Grand Wood Insert Fire SafetyCombustible/Non-combustible Materials Seasoned Wood Second Stage Voyageur Grand Wood Insert Burning ProcessKindling or First Stage Final Stage Burn Rates and Operating Efficiency Voyageur Grand Wood Insert Automatic Combustion Control ACCAir Controls Incorrect Positions Voyageur Grand Wood Insert Building a Fire Fuel Reloading Instructions Wood Fuel Moisture Blower Operating Instructions Opacity Smoke Frequently Asked QuestionsVoyageur Grand Wood Insert Clear Space Voyageur Grand Wood Insert Quick Start Guide Your specific model Cleaning Plated Surfaces Maintenance and ServiceChimney and Chimney Connector Inspection/Cleaning Disposal of Ashes Voyageur Grand Wood Insert Glass Cleaning Inspect Firebrick & Replacement Instructions Voyageur Grand Wood Insert Quick Reference Maintenance Guide Troubleshooting Guide Start Fire Problems Possible Cause Solution Snap Disc Replacement Contd Service Parts ReplacementGlass Replacement Snap Disc Replacement Voyageur Grand Wood Insert Blower Replacement Shock Risk 51mm. Figure Voyageur Grand Wood Insert Door Handle AssemblyBaffle & Ceramic Blanket Removal Voyageur Grand Wood Insert Tube Channel Assembly Replacement Draft Design and Installation ConsiderationsGetting Started Voyageur Grand Wood Insert Negative Pressure Voyageur Grand Wood Insert Locating Your Stove & Chimney Chimney Termination Requirements Voyageur Grand Wood Insert Rule Pre-Burn Check List Voyageur Grand Wood Insert Tools And Supplies NeededInspect Appliance and Components Dimensions and Clearances Appliance Dimensions Wall Clear of Ashes Converting k to R Thermal Conductivity k valueThermal Resistance R value Converting R to k Inspections Chimney SystemsVenting Systems Larger Chimneys Voyageur Grand Wood Insert Masonry Chimney Cont’d Voyageur Grand Wood Insert Metal Heat Circulating Masonry Prefabricated Metal Chimney Factory-Built Sold Fuel Fireplace Voyageur Grand Wood Insert Securing Chimney ComponentsAltering the Fireplace Chimney Height / Rise and Run Option One Outside Air Installation Instructions Outside Air Kit InstallationItems Needed for Installation not supplied Option Two Outside Air Installation Instructions Degree Leveling LegsFlue Adapter Vertical Standard Surround & Trim Kit Installation Voyageur Grand Wood Insert Standard Surround & Cast Trim Kit 42.1 Blower Cord Installation on Left Side Voyageur Grand Wood Insert All Cast Surround Kit Placement Slot Blower Access Assembly White Wire Mobile Home Installation Cast Iron Wood Insert Large Service PartsPart number list on following At Depot #10 Brick AssemblyStocked #7 Baffle Protection Channel #13 Door Assembly Description Comments Part Number #14 Access Assembly #17 Control Asembly #25 & 26 Surround Assemblies Voyageur Grand Wood Insert Service And Maintenance Log Date of Service Performed By Description of Service Voyageur Grand Wood Insert Service And Maintenance Log Voyageur Grand Wood Insert Homeowner’s Notes Contact Information