Manuals / Regency / Household Appliance / Indoor Fireplace

Regency Specifications, Note These units are non-loadbearing, P121-2See Thru, P131-2Pier

Models: P121LC P121 P121RC P131

1 48

Download 48 pages 21.81 Kb

Page 7

Image 7

INSTALLATION

SPECIFICATIONS

P121-2 See Thru

Note: These units are

non-load bearing.

P131-2 Pier

Regency® P121-2/P121LC-2/P121RC-2/P131-2 Zero Clearance Direct Vent Gas Fireplace

Page 7

Image 7

Regency P121RC, P121LC Specifications, Note These units are non-loadbearing, P121-2See Thru, P131-2Pier

Contents

P121 / P121LC / P121RC / P131 Installation ManualFOR YOUR SAFETY FOR YOUR SAFETY What to do if you smell gasMANUFACTURED MOBILE HOME REQUIREMENTS PARTS LIST SAFETY LABELINSTALLATION MAINTENANCECopy of Safety Decal for P121/P121LC/P121RC/P131 SAFETY LABELOBSTRUCTIONS REQUIREMENTSMA Code - CO Detector 5.08 Modifications to NFPA-54,ChapterBEFORE YOU START GENERAL SAFETY INFORMATIONINSTALLATION CHECKLIST IMPORTANT MESSAGE SAVE THESE INSTRUCTIONSP131-2Pier SPECIFICATIONSNote These units are non-loadbearing P121-2See ThruP121RC-2Right Corner Unit INSTALLATIONNote These units are non-loadbearing P121LC-2Left Corner UnitA P121-2See Thru B P131-2Pier LOCATING YOUR GAS FIREPLACED P121RC-2Right Corner COMBUSTIBLE MANTELS CLEARANCESMantel Clearances C A B Framing DimensionsFRAMING AND FINISHING Note These units are non-loadbearingVENTING INTRODUCTION UNIT ASSEMBLY PRIOR TO INSTALLATIONTop Standoff Assembly Facing & Finishing RequirementsEXTERIOR VENT TERMINATION LOCATIONS RIGID PIPE VENTING COMPONENTS LIST VENTING ARRANGEMENT - HORIZONTAL TERMINATIONS Wall Thickness Flat Wall InstallationRIGID PIPE VENTING SYSTEMS Horizontal or Vertical TerminationsHorizontal Venting with One 1 90o Elbow RIGID PIPE VENTING ARRANGEMENTSHORIZONTAL TERMINATIONS Straight Out Horizontal VentingHorizontal Venting with Three 3 90o Elbows Horizontal Venting with Two 2 90o ElbowsHorizontal Venting with Three 3 90o Elbows Horizontal Venting with Two 2 90o ElbowsOption Propane & Natural GasStraight Up Vertical Venting Vertical Venting with One 1 90o ElbowOption Vertical Venting with Two 2 90o ElbowsVertical Venting with Two 2 90o Elbows Vertical Venting with Three 3 90o ElbowsOption Install the vent system according to the manufacturers instructions included with the componentsHORIZONTAL TERMINATIONS Vertical Venting with Three 3 90o ElbowsDiagram DiagramDiagram Diagram DiagramOffset Chart INSTALLATION PROCEDURESfor Regency AstroCapTM Direct Vent System Flex CONVERSION KIT #731-969FROM NG TO LP Installation of LPG Conversion KitDiagram DiagramDo not over tighten the screw. Recommended to Installation of the DC SparkerWire Piezo Ignitor DC Sparker Ignitor Wirewith the appliance Installer Notice These instructions must be leftGround wire from kit Battery CompartmentHIGH ELEVATION PILOT ADJUSTMENTGAS LINE INSTALLATION GAS PIPE PRESSURE TESTING326 LOG INSTALLATIONPush back side of the left end of the log up against the tab on the burnerGrate Post Caution Do NOT cover burner portsGrate Post 328GLASS DOOR installed the same wayFINISHING TRIM LOUVERS & GRILLSwall thermostat wires REMOTE CONTROLWALL SWITCH switch wire to a 120V wireThermocouple WIRING DIAGRAMSAssembly SwitchElectrode ThermocoupleThermopile GasPilotAdjustment Wire - Push to close or SHUTDOWN PROCEDUREAERATION ADJUSTMENT LIGHTING PROCEDUREBurner Tray NORMAL OPERATING SOUNDS OF GAS APPLIANCESCOPY OF THE LIGHTING PLATE INSTRUCTIONS BlowerGeneral Vent Maintenance MAINTENANCE INSTRUCTIONSLOG REPLACEMENT GOLD-PLATED AccessoriesRemove Left & Right Side Base Brick Panels REMOVING VALVERemove the 2 Long Base Brick Panels FAN REPLACEMENT INSTALLING VALVEConnector wires P121-2SEE THRU MAIN ASSEMBLY PARTS LISTDescription P131-2PIER MAIN ASSEMBLYDescription Description P121RC-2RIGHT CORNER MAIN ASSEMBLYDescription Description P121LC-2LEFT CORNER MAIN ASSEMBLYDescription Description Part #Page Page Page Conditions WARRANTYExclusions thoroughly before it leaves our door