INSTALLATION
IMPORTANT MESSAGE
SAVE THESE
INSTRUCTIONS
The Panorama P121/P121LC/P121RC/P131-
BEFORE YOU START
Safe installation and operation of this appliance requires common sense, however, we are required by the Canadian Safety Standards and ANSI Standards to make you aware of the following:
INSTALLATIONANDREPAIRSHOULD BE DONE BY A QUALIFIED SERVICE PERSON. THE APPLIANCE SHOULD BE INSPECTED BEFORE USE AND AT LEAST ANNUALLY BY A PROFESSIONAL SERVICE PERSON. MORE FREQUENT CLEANING MAY BE REQUIRED DUE TO EXCESSIVE LINT FROM CARPETING, BEDDING MATERIAL, ETC. IT IS IMPERATIVE THAT CONTROL COMPARTMENTS, BURNERS AND CIRCULATING AIR PASSAGEWAYS OF THE APPLIANCE BE KEPT CLEAN.
DUE TO HIGH TEMPERATURES, THE APPLIANCE SHOULD BE LOCATED OUT OF TRAFFIC AND AWAY FROM FURNITURE AND DRAPERIES.
WARNING:FAILURETOINSTALLTHIS APPLIANCE CORRECTLY WILL VOID YOUR WARRANTY AND MAY CAUSE A SERIOUS HOUSE FIRE.
CLOTHING OR OTHER FLAMMABLE MATERIALSHOULD NOT BE PLACED ON OR NEAR THE APPLIANCE.
CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURES, ESPECIALLYTHEFIREPLACEGLASS, AND SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION.
YOUNG CHILDREN SHOULD BE
CAREFULLY SUPERVISED WHEN THEY ARE IN THE SAME ROOM AS THE APPLIANCE.
GENERAL SAFETY
INFORMATION
1)The appliance installation must conform with local codes or, in the absence of local codes, with the current Canadian or National Gas Codes,
2)See general construction and assembly instructions. The appliance and vent should be enclosed.
3)This appliance must be connected to the specifi ed vent and termination cap to the outside of the building envelope. Never vent to another room or inside a building. Make sure that the vent is fi tted as per Venting instructions.
4)Inspect the venting system annually for blockage and any signs of deterioration.
5)Venting terminals shall not be recessed into a wall or siding.
6)Any safety glass removed for servicing must be replaced prior to operating the appliance.
7)To prevent injury, do not allow anyone who is unfamiliar with the operation to use the fi replace.
8)Wearglovesandsafetyglassesforprotection while doing required maintenance.
9)Be aware of electrical wiring locations in walls and ceilings when cutting holes for termination.
10)Under no circumstances should this appliance be modifi ed. Parts that have to be removed for servicing should be replaced prior to operating this appliance.
11)Installation and any repairs to this appliance shouldbedonebyaqualifiedserviceperson. A professional service person should be called to inspect this appliance annually. Make it a practice to have all of your gas appliances checked annually.
12)Do not slam shut or strike the glass door.
13)Under no circumstances should any solid fuels (wood, paper, cardboard, coal, etc.) be used in this appliance.
14)The appliance area must be kept clear and free of combustible materials, (gases and other fl ammable vapours and liquids).
Emissions from burning wood or gas could contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
INSTALLATION
CHECKLIST
Note: These units are
1)Locate appliance. Refer to the following sections:
a)Locating Your Fireplace
b)Clearances
c)Combustible Mantel Clearances
d)Framing & Finishing
e)Venting. See the "Venting Introduction" to "Venting Arrangements" sections.
2)Assemble Top Standoffs. Refer to the "Unit Assembly Prior to Installation" section. (NOTE: must be done before installing unit into fi replace.)
3)Install vent. See the "Horizontal Installations" to "Installation Procedures" sections
4)Make gas connections. Test the pilot. Must be as per diagram. Refer to the "Gas Line Installation" & "Pilot Adjustment" sections.
5)Install standard and optional features. Refer to the following sections where applicable: a. Log Set
b. Glass Door c. Finishing Trim d. Louvers & Grills e. Remote Control f. Wall Switch
g. Wall Thermostat
6)Final check.
Before leaving this unit with the customer, the installer must ensure that the appliance is
firing correctly and operation fully explained to customer.
This includes:
1)Clocking the appliance to ensure the correct fi ring rate (rate noted on label 40,000 Btu/h NG, and 39,000 Btu/h LP) after burning appliance for 15 minutes.
2)Ifrequired,adjustingtheprimaryairtoensure that the fl ame does not carbon. First allow the unit to burn for
CAUTION: Any alteration to the product that causes sooting or carboning that results in damage is not the responsibility of the manufacturer.
6 | Regency® |
