Manuals / Ricoh / Computer Equipment / All in One Printer

Ricoh FT1208, 1008 manual Condition, Cause, Remedy, Page

Models: FT1208 1008

1 65

Download 65 pages 33.01 Kb

Page 54

Condition

	Condition	Cause	Remedy			See
	Condition	Cause	Remedy			Page
						Page

		Power cord is not properly	Plug it in firmly.			-
		plugged into the outlet.	Plug it in firmly.
		plugged into the outlet.

	Nothing happens		Check that the both ends of
	when the switch is		the top unit are securely
	turned on.	Top unit is not completely	closed. If not, close the top			15
		closed.	unit firmly by pressing the
			marked	position.

	PE is displayed on	Paper cassette is empty.	Load paper.			18
	the copy counter.	Paper cassette is empty.	Load paper.			18
	the copy counter.

	L&I is blinking.	Toner has nearly run out	Replace	toner	cassette.	42

	L&l stays on.	Toner has run out.	Replace	toner	cassette.	42

	& stays on.	A misfeed has occurred.	Clear misfed paper.			59

	The copier has
	entered Auto-off	The copier has shifted to the	Press any key to re-activate
	mode (30 minutes	The copier has shifted to the	Press any key to re-activate			21
	after a copy was	Auto-off function.	the copier.			21
	made or a key was
	pressed).

	Copies have white
	streaks.	Corona wires are dirty.	Clean the corona wires.			45

	Copy image
	Copy image
	density is uneven.

	t’ i is displayed on	The copier is overheated.	Wait for a while until the
	t’ i is displayed on		copier cools down and t’ I is			48
	the copy counter.		copier cools down and t’ I is			48
	the copy counter.		no longer displayed.
			no longer displayed.

ATTENTION: If the error code (E ..) appears, turn off the main switch, then turn it on. If the error code disappears, the copier will function. If the error code appears again, turn off the main switch and immediately call your service personnel.

56

Image 54

Ricoh FT1208, 1008 manual Condition, Cause, Remedy, Page

Contents

For safety. please follow the instructions in this manual RICOH FT1008/1208OPERATOR’S MANUAL For details, see pages ESSENTIAL SYMBOLS 8 Avoid using an extension Page 4 . Operation Panel 1. Main Switch2 . Exposure Glass 5. Paper Cassette2 . Toner Cassette 3. Fusing Unit4. Image Density Recalibration Switch 6 . Guide PlatesQpe1&2 @ Preset Reduce/Enlarge Key Auto Start - Setting Copy Orders During Warm-Up 20-21Auto-off mode - for automatically saving power NOTES ON INSTALLATION LOCATIONMAINTAINING 36-3737-40 CLEARING MISFEEDS14-19 INSTALLATIONInstalling Copier UnpackingPage Page Remove the toner cassette from the vinyl bag Remove the end plate @ and set it to your desired paper size Page When you copy onto long-size paper, extend-the copy tray as shown Confirm that the copy tray is securely in placeFirmly insert the plug into the copier and outlet Turn the main switch onPower Connection Turning Copier OnAuto-off mode - for automatically saving power Copier Location PLACEMENT OF ORIGINALS ADJUSTING COPY DENSITYAuto Start - Setting Copy Orders Reducing/Enlarging Using Preset RatiosAlignment of Originals Auto Start - Setting Copy Orders During Warm-Up 0++ +o1,z 3 , . . . . . . . . . . . . . . . . . . . . 48,49,50 One sheet should be inserted into the bypass feed at a time Set the originals and letterhead as shown copies are as followsSet the originals and transparencies as shown TransparenciesPage Page Page Press the Start key to make the first copy Page Page Close the top unit by pressing down firmly on the marked posi GD tion Auto reset duration Adjustable itemPhoto mode level User ToolPage Adjusting values/modes 1. Auto image density levelUser modeNumber 60 minutes 10 minutes30 minutes 90 minutesDefault 1 minute Number For the second two digits, the center image density indicator is lit 45-46 MAINTAINING THE COPIER44-47 PaperOpen the top unit Remove the used toner cassette carefully Page Platen Cover C o p y TrayBypass Feed Page Close the top unit by pressing down firmly on the marked posi- tion Remove the tool from the transfer corona wire and store it as shownm @B Keep this tool inside the copierClose the top unit by pressing down firmly on the marked posi- tion Attension Make sure to press the marked positionAlways turn the copier off when you have finished copying for the day When you make 150 or more copies continuouslyWhen you make solid full image copies Under the following conditions, you might get light copiesDo not leave any tom scraps of paper inside the copier Store horizontally in a cool, dark place Never store toner cassette where it will be exposed to heatUse older stock first Do not lay heavy objects on paper Do not lay heavy objects on the toner cassettePage Put the toner cassette in a vinyl bag Put the copier in the cardboard box operator’s manual and power cord into the boxam Seal the box firmly using tape Insert the toner cassette, copy trayWhen & stays on TROUBLESHOOTINGWhen Pz appears on the copy counter CLEARING MISFEEDSRemedy ConditionCause PageRemedy ConditionCause Set proper paper. PaperPage When PE appears on the copy counter When & is lit Make sure that the Check Paper Path & indicator is turned offSPECIFICATIONS 62-63Configuration Dimensions Paper Capacity Toner Replenishment Copy Tray Capacity Power SourcePower Consumption Noise Emission WeightPage Page I means POWER ON.1 0 means POWER OFFDeclaration of Conformity U.S.A EE@rnm~n Overseas Affiliates The Netherlands