Install the Leveling Feet, Mounting the Motor | RIDGID JP06101

Assembly (continued)

Install the Leveling Feet

1.Turn the base upside down.

2.From the hardware pack find the following:

4 Rubber Leveling Feet

8 Flat Washer 3/8

8 Hex Nut 3/8

3.Thread one 3/8 nut onto each of the leveling feet until the nut is 1/2" from the foot. Do this for all four feet.

4.Attach the leveling feet as shown. Place one 3/8 washer on the bottom side of the foot mount tab and one washer on top. Bolt the feet in place with the sec- ond 3/8 nut. Tighten the nuts down with a wrench.

NOTE: Once the jointer is in its permanent location the leveling feet may need to be adjusted.

	3/8 Flat Washer
Leveling Foot	Leveling Foot
	Leveling Foot

3/8-16 Hex Nut Cabinet ˜

Mounting the Motor

1.Turn the cabinet upside down and place a 4 x 4 block under the right side of the cabinet so the base is tilted as shown. This will elevate the motor mount so it is level with the floor making assembly easier.

2.From the hardware pack find the following:

4Carriage Head Bolts 5/16-18 x 1/2"

4Serrated Flange Hex Nuts 5/16

2Machine Screws with Washer Head 3/16" From among the loose parts find the following:

1Motor and Switch Assembly

3.Place the motor on the motor mount as shown. Make sure the motor shaft faces the rear of the cabinet (away from the side with RIDGID label).

4.Bolt the motor to the motor mount using the four 5/16 car- riage head bolts and four 5/16 serrated flange nuts. The bolts should be placed through the motor mount into the motor bracket as shown. Do not tighten the bolts at this time.

5.Using the two 3/16 screws, mount the switch into place as shown. Make sure the switch is right side up.

Carriage Head Bolt 5/16-18 x 1/2"

Serrated Flange

Hex Nut 5/16

Machine Screw w/Washer Head 3/16-24 x 3/8

Motor Assembly with Switch

14

Image 14

RIDGID JP06101 manual Install the Leveling Feet, Mounting the Motor, Motor Assembly with Switch

Contents

235$725·60$18$ Table of Contents Safety Instructions For Jointer/Planer Before Using the Jointer/Planer Major Hazards Safety Labels and Indicators on the Jointer/Planer Plan Ahead To Protect Your Eyes, Hands, Face and Ears Inspect Your Workpiece Keep Children Away Whenever Jointer/Planer Is RunningBefore Leaving the Jointer/Planer Don’t Force Tool Glossary of Terms for Woodworking Motor Specifications and Electrical RequirementsPower Supply and Motor Specifications Changing Motor Voltage General Electrical ConnectionsVolt, 60 Hz. Tool Information Prong Plug Properly Grounded Outlet Grounding Extension Gauge A.W.G Cord Length Motor Safety ProtectionWire Sizes Unpacking and Checking Contents Loose Parts Hex Nut 16-18 Loose Parts From Hardware PackHex Nut Assembly Cabinet and Motor Mount Assembly Mounting the Motor Install the Leveling FeetMotor Assembly with Switch Belt Tensioning Belt and Installing Rear PanelMounting Jointer Table to Cabinet Align Belt Tighten Motor Mount Nuts Serr 3/16-24 x 3/8 Belt Guard Installing the Pulley GuardInstalling Handwheel 20 x 5/8 Tool Storage Sawdust Chute Screw Wing 1/4-20 x 1/2 Adjusting Table ExtensionAttach Sawdust Chute Outfeed Socket Head Screw Extension even with Outfeed table Assemble Fence To Bed Install Cutter Head GuardAssembly Fence Nut Mount Fence Lock Knob Nut Washer 1/2 Actual Size Not Cutter Head Guard Functional Check Adjusting Guard SpringAdjusting the Leveling Feet Pan Head Screw Knob Depth of Cut Handwheel Getting to Know Your Jointer/PlanerFence Sliding Knob Nameplate Model/Serial Fence Tilt Bevel Knob On-Off Switch Cutter Knife Alignment/Adjustments Alignments Cutter Knife Sharpening 11/16 Wide New Blade Second Cutting Ground Surface Edge Outfeed Table Too High Result Outfeed Table AdjustmentChecking Outfeed Table Alignment Outfeed Table Too Low Result Angle Gauge Use Adjusting Table GibsFence Tilt Use and Bevel Stop Adjustment Stop Screw Bar Fence Slide Lock Knob Bevel Lock Handle Safety Instructions for Basic Jointer/Planer OperationBefore Each Use Push blocks and push sticks Always Use Push Blocks When Planing, Beveling Or ChamferingFeeding the Workpiece All Operations Plan your work Inspect your workpiece Before Leaving the jointer/planer Stop Pin Operation Basic Jointer/Planer Cutting OperationsDepth of Cut Handwheel Operation Feeding the Workpiece Beveling/Chamfering PlaningJointing Jointing Without Push Blocks Support Long Workpieces Using the Hold-Down/Push-BlocksRabbeting Face Rabbet End Edge Sliding Fence Operation Sliding Lock Knob Maintenance Maintenance and LubricationWiring Diagram Lubrication Trouble Probable Cause Remedy Troubleshooting GuideGeneral Motor Repair Parts Parts List for Ridgid 6-1/8 Jointer/Planer Model No. JP06101 Always order by Part Number Not by Key Number Description Key Description Repair Parts Repair Parts Repair Parts Repair Parts Repair Parts JEG6 DAY Satisfaction Guarantee Policy Call