Loose Parts, Dust BAG | RIDGID MS1290LZA guide

LOOSE PARTS

The following items are included with your miter saw:

Dust Bag

Dust Bag Frame

Dust Guide

Work Clamp

DUST BAG

DUST BAG	LASER
FRAME	GUIDE

FLAT HEAD

SOCKET CAP

SCREW

Blade Wrench

Hex Key, 1/16 in.

Laser Guide

Flat Head Socket Cap Screw

Operator’s Manual (not shown)

WORK CLAMP

HEX KEY,

1/16 in.

BLADE

WRENCH

DUST

GUIDE

Fig. 7

WARNING:

The use of attachments or accessories not listed in this manual might be hazardous and could cause serious personal injury.

Page 14

Image 14

RIDGID MS1290LZA manual Loose Parts, Dust BAG, Flat Head Socket CAP Screw, Work Clamp HEX KEY Blade Wrench Dust Guide

Contents

OPERATOR’S Manual MS1290LZA Table of Contents Introduction  Blade Coasts After Being Turned OFF General Safety RulesRead ALL Instructions Specific Safety Rules  Before Making a CUT, be Sure ALL ADJUST- Ments are Secure Specific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATION Service Symbol Signal Meaning Double Insulation Cord Length Wire Size A.W.GElectrical Electrical Connection Glossary of Terms Features Product Specifications AMP Motor Know Your Compound Miter SAW12 IN. Blade Bevel Lock Lever Miter Scale Switch TriggerMiter Lock Lever Miter Thumbwheel Combination Square Tools NeededRatchet Phillips Screwdriver Framing Square Flat Head Socket CAP Screw Loose PartsDust BAG Work Clamp HEX KEY Blade Wrench Dust Guide Mounting Holes AssemblyUnpacking SAW ARM Using the Depth GuideLocking / Unlocking the SAW ARM Depth Guide Dust BAG Frame Guide Exhaust Port Installing the Dust BAGInstalling the Work Clamp Work Clamp Installing / Replacing the Blade To Cut the Mark Aligning the Laser Guide LineRemoving the Mark To Leave the Mark Removing / Replacing the Zero CLEAR- Ance Throat Plate Centering the SAW Blade Between the Slide Bars Squaring the SAW Blade to the Fence Adjusting the Miter Lock LeverTo adjust See Figures 17 Indicator Fig View of Blade Square with Fence Miter Scale Travel Pivot Adjustment Adjusting the Bevel Lock LeverAdjusting the Bevel Pivot Bevel Lock Lever Lift to Unlock See Figures 27 IndicatorSquaring the Blade to the Miter Table Sliding Miter Fence Cutting with Your Sliding Compound Miter SAW OperationApplications Slide CUT Slide SAW ARM Forward then Push Down Back To Slide CUTSee Figures 31 Work Clamp To Miter CUT / Cross CUTSee Figures 33 Cross CUT Work Clamp Miter CUT See Figures 35 Scale Indicator BevelTo Bevel CUT Bevel CUT Clamp Lock PIN To Compound Miter CUT Compound Miter CUT Long Workpiece Supporting Long WorkpiecesClamping Wide Workpieces 45 x 45 Compound Miter CUT Depth Guide CUT These Grooves With SAW Using AN Auxiliary FenceRough Cutting a Dado Auxiliary Fence Pitch Side COMPOUND-ANGLE Settings for Popular StructuresCutting Compound Miters Ceiling Cutting Crown MoldingLaying Molding Flat on the Miter Table Inside Corner Fence Crown Molding JIG Using a Crown Molding Support JIGMaking a Crown Molding Support JIG Adjustment Screw Laser Button Aperture HEX KEY Mark AdjustmentsTo Adjust the Laser Guide Cutting Warped Material Brush Replacement MaintenanceGeneral Maintenance Lubrication Motor Belt Tension To adjust belt tensionScrew Battery Cover Batteries Negative Changing the Batteries Accessories Miter Saw Utility Vehicle What is Covered Under the 3 Year Limited Service Warranty WarrantyDAY Satisfaction Guarantee Policy HOW to Obtain Service What is not Covered MS1290LZA Customer Service InformationModel No Serial No