Customer Service Information, Model No | RIDGID MS1290LZA manual

OPERATOR’S MANUAL

12 in. SLIDING COMPOUND MITER SAW WITH LASER

Double Insulated

MS1290LZA

CUSTOMER SERVICE INFORMATION

For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www.ridgid.com.

The model number of this tool is found on a plate attached to the motor housing. Please record the serial number in the space provided below. When ordering repair parts, always give the following information:

Model No.		MS1290LZA
Model No.
Serial No.
Serial No.

987000-017

8-16-07 (REV: 01)

Page 40

Image 40

RIDGID MS1290LZA manual Customer Service Information, Model No, Serial No

Contents

OPERATOR’S Manual MS1290LZA Table of Contents Introduction Read ALL Instructions General Safety Rules Blade Coasts After Being Turned OFF Specific Safety Rules  Before Making a CUT, be Sure ALL ADJUST- Ments are Secure Specific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATION Service Symbol Signal Meaning Cord Length Wire Size A.W.G ElectricalDouble Insulation Electrical Connection Glossary of Terms Features Product Specifications Know Your Compound Miter SAW 12 IN. BladeAMP Motor Bevel Lock Lever Switch Trigger Miter Lock LeverMiter Scale Miter Thumbwheel Tools Needed RatchetCombination Square Phillips Screwdriver Framing Square Loose Parts Dust BAGFlat Head Socket CAP Screw Work Clamp HEX KEY Blade Wrench Dust Guide Unpacking AssemblyMounting Holes Using the Depth Guide Locking / Unlocking the SAW ARMSAW ARM Depth Guide Installing the Dust BAG Installing the Work ClampDust BAG Frame Guide Exhaust Port Work Clamp Installing / Replacing the Blade Aligning the Laser Guide Line Removing the MarkTo Cut the Mark To Leave the Mark Removing / Replacing the Zero CLEAR- Ance Throat Plate Centering the SAW Blade Between the Slide Bars Adjusting the Miter Lock Lever To adjustSquaring the SAW Blade to the Fence See Figures 17 Indicator Fig View of Blade Square with Fence Miter Scale Adjusting the Bevel Lock Lever Adjusting the Bevel PivotTravel Pivot Adjustment Bevel Lock Lever Lift to Unlock Indicator Squaring the Blade to the Miter TableSee Figures 27 Sliding Miter Fence Applications OperationCutting with Your Sliding Compound Miter SAW See Figures 31 To Slide CUTSlide CUT Slide SAW ARM Forward then Push Down Back To Miter CUT / Cross CUT See Figures 33Work Clamp Cross CUT Work Clamp Miter CUT Scale Indicator Bevel To Bevel CUTSee Figures 35 Bevel CUT Clamp Lock PIN To Compound Miter CUT Compound Miter CUT Supporting Long Workpieces Clamping Wide WorkpiecesLong Workpiece 45 x 45 Compound Miter CUT Using AN Auxiliary Fence Rough Cutting a DadoDepth Guide CUT These Grooves With SAW Auxiliary Fence Cutting Compound Miters COMPOUND-ANGLE Settings for Popular StructuresPitch Side Cutting Crown Molding Laying Molding Flat on the Miter TableCeiling Inside Corner Fence Making a Crown Molding Support JIG Using a Crown Molding Support JIGCrown Molding JIG Adjustments To Adjust the Laser GuideAdjustment Screw Laser Button Aperture HEX KEY Mark Cutting Warped Material Maintenance General MaintenanceBrush Replacement Lubrication To adjust belt tension Screw Battery Cover Batteries NegativeMotor Belt Tension Changing the Batteries Accessories Miter Saw Utility Vehicle Warranty DAY Satisfaction Guarantee PolicyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not Covered Customer Service Information Model NoMS1290LZA Serial No

OPERATOR’S MANUAL

12 in. SLIDING COMPOUND MITER SAW WITH LASER

MS1290LZA

CUSTOMER SERVICE INFORMATION

Model No.

MS1290LZA

Serial No.