TECHNICAL DATA
| WEIGHT |
|
| DIMENSIONS |
|
|
|
| GAS RATE (BTU/h) |
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| 51 Lbs. |
|
| Width: 29 1/2" |
|
|
| INPUT |
|
|
| OUTPUT |
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
| Height:21 13/16" |
|
|
|
| NG | LP |
|
| NG | LP |
|
|
|
|
|
|
|
| |||||
|
|
|
|
| Depth: 9 13/16" |
|
| LOW | 8,200 | 8,200 |
| LOW | 6,640 | 6,640 |
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
| HIGH | 16,700 16,700 |
| HIGH | 13,400 13,400 |
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Burner Orifices: |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||||||
|
|
|
|
|
|
|
| GAS CONVERSION SPECIFICATIONS |
|
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
MODEL | GAS |
| DIAMETER OF | PRIMARY |
| SECONDARY | MANIFOLD DIFFERENTIAL | DIP SWITCH | ||||||||||||||||||||
|
|
| TYPE | ORIFICE(mm) | DAMPER |
| DAMPER | PRESSURE (W.C.) | POSITION | |||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| HI |
|
| LO |
|
|
|
|
|
|
|
|
NG |
| 1.13 |
| 2.4"W.C. |
| 0.7"W.C. | ON |
|
|
|
|
| ||||||||||||||||
|
|
|
|
|
|
|
|
|
| |||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| (33×47hole) |
|
|
|
|
| OFF |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
LPG |
| 0.85 |
| 2.8"W.C. |
| 0.8"W.C. | ON |
|
|
|
|
|
|
| ||||||||||||||
|
|
|
|
|
|
|
|
|
| |||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ( 2.5×15) |
|
|
|
|
| OFF |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
GAS SUPPLY PRESSURE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
| NATURAL | PROPANE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
MINIMUM |
| 3.5"W.C. |
| 8"W.C. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
MAXIMUM |
| 10.5"W.C. |
| 13"W.C. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
・The minimum inlet gas supply pressures is for the purpose of input adjustment. ・Heaters may be converted from one gas to another using Rinnai conversion kits.
IMPORTANT POINTS / USAGE AND INSTALLATION MUSTS
Unpack heater and check for damage. (DO NOT INSTALL DAMAGED HEATER.) If heater is damaged, contact your supplier for advice. Before installing a heater, check the label for the correct gas type (see label on side of heater). Refer to local gas authority for confirmation of gas type if you are in doubt.
Included in Carton:
・Customers Operating Information ・Conversion kits
IMPORTANT
Before using this product, please read this manual carefully to insure proper use of product.
1.The installation must conform with local codes or, in absence of local codes, the National Fuel Gas Code, ANSI Z223.1 or the Canadian Installation Code,
2.For information on gas type, see data plate on the appliance.
3.This heater must not be installed where curtains or other combustible materials could come into contact with it. In some cases curtains may need restraining.
–2 –