LS-3/LS-5 Dimensions | Runco specification

Specifications

7.2

LS-3/LS-5 Dimensions

Figure 7-1shows the LS-3/LS-5 dimensions, in millimeters.

200

530

150

455

80

75

160

LENS CENTER LINE

135

APPROXIMATE CENTER OF GRAVITY

CEILING MOUNT HOLES

M4 x 10mm MAXIMUM (4x)

Figure 7-1. LS-3/LS-5 Dimensions

86	Runco LS-3/LS-5 Installation/Operation Manual

Image 102

Runco operation manual LS-3/LS-5 Dimensions, 1shows the LS-3/LS-5 dimensions, in millimeters

Contents

LS-3 Series LS-5 Series LS-3 LS-3/CineWide LS-5 LS-5/CineWidePage RuncoCare Standard Two Year Limited Warranty RuncoCare Standard Features RuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of Conformity FCC Part Page Table of Contents Maintenance and Troubleshooting Operation Specifications Serial Communications Table of Contents Xiv List of Figures List of Figures Xvi Introduction About This Manual Using This Manual If you need Turn to Description, Features and Benefits Additional Features of the LS-5 Controls and Functions LS-3/LS-5 at a Glance Source LS-3/LS-5 Rear/Bottom/Top View Runco Logo Badge Page Page LS-3/LS-5 Remote Control Projector on PIP Installation Remote ControlOperation IR Reception Angles Step Procedure Quick SetupInstallation Overview For Details, Refer Installation Type InstallationProjector Installation Options Considerations Ambient Light Throw Distance Throw Ratios for the LS-3/LS-5 Series Vertical and HorizontalPosition Lens Shift Horizontal Lens Shift Example Only Installing the Optional CineWide Lens Mount Folded OpticsOther Considerations Installing the Fixed CineWide Base PlateDo not use the mounting screws provided with the ceiling Mounting the LS-3/LS-5 Connector Panel Access Connections toLS-3/LS-5 Connecting Source Components to the LS-3/LS-5 HDMI/DVI Connections See Figure RGB Connections Page 11. Composite and S-Video Connections RS-232 Controller Connection Trigger Output to External Connecting 12-VoltConnecting an External IR Theater Equipment Focus and Zoom Lens Shift Turning on the Power Lens AdjustmentsConnecting to AC Power Zoom Out Focus Zoom Installation Changing the OSD Language Adjusting the Picture Orientation Rear Projection Ceiling Mode Installing and Adjusting the CineWide Anamorphic Lens It is extremely important that the primary lens is properly Adjusting the Lens Height and Angle Correct Lens Angle Incorrect Lens Angle Selecting an Aspect Ratio OperationSelecting Video Memory Selecting An Input Source PIP Input Source Using Picture-In-Picture PIPAvailable Main and PIP Source Combinations Main Using the On-Screen Menus LS-3/LS-5 OSD Menu Structure Main LS-3/LS-5 Main Menu Aspect Ratio Settings 169 169 Narrow Native You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Operation Overscan Examples Source Select Sub-Menu Advanced LS-3/LS-5 Advanced Menu Operation X/y Color Gamut Values Color RGB Adjust Sub-Menu 10. Fine Sync Sub-Menu Operation System 11. LS-3/LS-5 System Menu 12. Source Enable Sub-Menu PBP1 PBP2 14. PIP Split-Screen Mode Control Page Language 15. LS-3/LS-5 Service Menu OSD menus are not available when in test pattern mode Operation Maintenance and Troubleshooting Lamp Replacement Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting Key Commands Serial Communications Serial Command Key Names and IR Codes RS232 Remote Button IR Code Description Keyname Set Gam.crt Operations Control Commands Function Action on unit Lit.tog Serial Commands Operation Commands Values Save.mem Source.sel = ? Satco = ? Auto.pow.off = ? Act.source Status RS-232 Error Codes Error Code LED Indication DescriptionPage LS-3/LS-5 Specifications Operating Temperature DimensionsWeight without lens Universal Power Supply LS-3/LS-5 Dimensions 1shows the LS-3/LS-5 dimensions, in millimeters Supported Signal Timings by Input Supported Timings PAL-B/G