Controls and Functions, LS-3/LS-5 at a Glance | Runco instruction

Controls and Functions

2. Controls and Functions

Figure 2-1and Figure 2-2show the key LS-3/LS-5 components.

2.1

LS-3/LS-5 at a Glance

System Keypad

Top IR Sensor

Power Button/ Status LED

Exhaust Vent (on side)

	Intake	Focus Ring
	Intake	Projection Lens
	Vent	Projection Lens

Front

IR Sensor

Zoom Ring

Figure 2-1. LS-3/LS-5 Front/Side View

•TOP IR SENSOR

Receives infrared signals from the remote control unit.

•POWER BUTTON/STATUS LED Indicates projector status as follows:

•Solid green = AC power present, ready to turn on (lamp not lit)

•Flashing green = lamp is warming up or cooling down; keypad functions not allowed

•Off = Lamp lit, projector functioning normally

•Alternating green/red = Lamp problem (door open, unable to strike, end of life), user intervention likely to fix problem

•Flashing red = Over temperature, user intervention (clear vents, turn on AC) may fix problem

•Solid red = Error that requires servicing (fan fail, Power-on self-test fail etc.)

•EXHAUST VENT

Warm air exits the projector through this vent. Ensure that it is not blocked.

•FOCUS RING

Rotate this to focus the projected image.

•PROJECTION LENS

Available in two versions: standard throw range (1.85:1 to 2.40:1) and short throw range (1.56:1 to 1.86:1).

Runco LS-3/LS-5 Installation/Operation Manual

5

Image 21

Runco operation manual Controls and Functions, LS-3/LS-5 at a Glance

Contents

LS-3 LS-3/CineWide LS-5 LS-5/CineWide LS-3 Series LS-5 SeriesPage RuncoCare Standard Features RuncoCare Standard Two Year Limited Warranty RuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance Information FCC Part Page Table of Contents Operation Maintenance and Troubleshooting Serial Communications Specifications Table of Contents Xiv List of Figures List of Figures Xvi About This Manual Introduction If you need Turn to Using This Manual Description, Features and Benefits Additional Features of the LS-5 LS-3/LS-5 at a Glance Controls and Functions Source LS-3/LS-5 Rear/Bottom/Top View Runco Logo Badge Page Page Projector on LS-3/LS-5 Remote Control PIP Installation Remote ControlOperation IR Reception Angles Installation Overview Quick SetupStep Procedure For Details, Refer Projector Installation Options InstallationInstallation Type Considerations Throw Distance Ambient Light Throw Ratios for the LS-3/LS-5 Series Vertical and HorizontalPosition Lens Shift Horizontal Lens Shift Example Only Installing the Optional CineWide Lens Mount Folded OpticsOther Considerations Installing the Fixed CineWide Base PlateDo not use the mounting screws provided with the ceiling Mounting the LS-3/LS-5 Connector Panel Access Connections toLS-3/LS-5 HDMI/DVI Connections See Figure Connecting Source Components to the LS-3/LS-5 RGB Connections Page 11. Composite and S-Video Connections Connection RS-232 Controller Connecting an External IR Connecting 12-VoltTrigger Output to External Theater Equipment Connecting to AC Power Turning on the Power Lens AdjustmentsFocus and Zoom Lens Shift Zoom Out Focus Zoom Installation Rear Projection Ceiling Mode Changing the OSD Language Adjusting the Picture Orientation It is extremely important that the primary lens is properly Installing and Adjusting the CineWide Anamorphic Lens Adjusting the Lens Height and Angle Correct Lens Angle Incorrect Lens Angle Selecting Video Memory OperationSelecting an Aspect Ratio Selecting An Input Source Available Main and PIP Source Combinations Using Picture-In-Picture PIPPIP Input Source Main Using the On-Screen Menus LS-3/LS-5 OSD Menu Structure LS-3/LS-5 Main Menu Main 169 Aspect Ratio Settings Narrow 169 Native You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Operation Overscan Examples Source Select Sub-Menu LS-3/LS-5 Advanced Menu Advanced Operation Color X/y Color Gamut Values RGB Adjust Sub-Menu 10. Fine Sync Sub-Menu Operation 11. LS-3/LS-5 System Menu System 12. Source Enable Sub-Menu PBP1 PBP2 14. PIP Split-Screen Mode Control Page Language 15. LS-3/LS-5 Service Menu OSD menus are not available when in test pattern mode Operation Lamp Replacement Maintenance and Troubleshooting Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting Serial Communications Key Commands RS232 Remote Button IR Code Description Keyname Set Serial Command Key Names and IR Codes Gam.crt Lit.tog Operations Control Commands Function Action on unit Operation Commands Values Serial Commands Save.mem Source.sel = ? Satco = ? Auto.pow.off = ? Act.source Status Error Code LED Indication Description RS-232 Error CodesPage LS-3/LS-5 Specifications Weight without lens DimensionsOperating Temperature Universal Power Supply 1shows the LS-3/LS-5 dimensions, in millimeters LS-3/LS-5 Dimensions Supported Timings Supported Signal Timings by Input PAL-B/G