Serial Communications, Specifications | Runco LS-3, LS-5 specs

		Table of Contents
6.	Serial Communications	71
	RS-232 Connection and Port Configuration	71
	Serial Command Syntax	71
	Key Commands	71
	Operations Commands	74
	RS-232 Error Codes	82
7.	Specifications	83
	LS-3/LS-5 Specifications	83
	LS-3/LS-5 Dimensions	86
	Supported Timings	87

Runco LS-3/LS-5 Installation/Operation Manual

xiii

Image 13

Runco LS-3, LS-5 operation manual Serial Communications, Specifications

Contents

LS-3 LS-3/CineWide LS-5 LS-5/CineWide LS-3 Series LS-5 SeriesPage RuncoCare Standard Features RuncoCare Standard Two Year Limited Warranty RuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance Information FCC Part Page Table of Contents Operation Maintenance and Troubleshooting Serial Communications Specifications Table of Contents Xiv List of Figures List of Figures Xvi About This Manual Introduction If you need Turn to Using This Manual Description, Features and Benefits Additional Features of the LS-5 LS-3/LS-5 at a Glance Controls and Functions Source LS-3/LS-5 Rear/Bottom/Top View Runco Logo Badge Page Page Projector on LS-3/LS-5 Remote Control PIP Remote Control InstallationOperation IR Reception Angles Installation Overview Quick SetupStep Procedure For Details, Refer Projector Installation Options InstallationInstallation Type Considerations Throw Distance Ambient Light Vertical and Horizontal Throw Ratios for the LS-3/LS-5 SeriesPosition Lens Shift Horizontal Lens Shift Example Only Folded Optics Installing the Optional CineWide Lens MountOther Considerations CineWide Base Plate Installing the FixedDo not use the mounting screws provided with the ceiling Mounting the LS-3/LS-5 Connections to Connector Panel AccessLS-3/LS-5 HDMI/DVI Connections See Figure Connecting Source Components to the LS-3/LS-5 RGB Connections Page 11. Composite and S-Video Connections Connection RS-232 Controller Connecting an External IR Connecting 12-VoltTrigger Output to External Theater Equipment Connecting to AC Power Turning on the Power Lens AdjustmentsFocus and Zoom Lens Shift Zoom Out Focus Zoom Installation Rear Projection Ceiling Mode Changing the OSD Language Adjusting the Picture Orientation It is extremely important that the primary lens is properly Installing and Adjusting the CineWide Anamorphic Lens Adjusting the Lens Height and Angle Correct Lens Angle Incorrect Lens Angle Selecting Video Memory OperationSelecting an Aspect Ratio Selecting An Input Source Available Main and PIP Source Combinations Using Picture-In-Picture PIPPIP Input Source Main Using the On-Screen Menus LS-3/LS-5 OSD Menu Structure LS-3/LS-5 Main Menu Main 169 Aspect Ratio Settings Narrow 169 Native You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Operation Overscan Examples Source Select Sub-Menu LS-3/LS-5 Advanced Menu Advanced Operation Color X/y Color Gamut Values RGB Adjust Sub-Menu 10. Fine Sync Sub-Menu Operation 11. LS-3/LS-5 System Menu System 12. Source Enable Sub-Menu PBP1 PBP2 14. PIP Split-Screen Mode Control Page Language 15. LS-3/LS-5 Service Menu OSD menus are not available when in test pattern mode Operation Lamp Replacement Maintenance and Troubleshooting Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting Serial Communications Key Commands RS232 Remote Button IR Code Description Keyname Set Serial Command Key Names and IR Codes Gam.crt Lit.tog Operations Control Commands Function Action on unit Operation Commands Values Serial Commands Save.mem Source.sel = ? Satco = ? Auto.pow.off = ? Act.source Status Error Code LED Indication Description RS-232 Error CodesPage LS-3/LS-5 Specifications Weight without lens DimensionsOperating Temperature Universal Power Supply 1shows the LS-3/LS-5 dimensions, in millimeters LS-3/LS-5 Dimensions Supported Timings Supported Signal Timings by Input PAL-B/G