Operation, Maintenance and Troubleshooting | Runco LS-5, LS-3

Table of Contents

	Mounting the LS-3/LS-5	23
	Floor Mounting (Upright)	23
	Ceiling Mounting (Inverted)	23
	Adjusting the Projection Angle	23
	Connections to the LS-3/LS-5	24
	Connector Panel Access	24
	Connecting Source Components to the LS-3/LS-5	25
	RS-232 Controller Connection	29
	Connecting 12-Volt Trigger Output to External Theater Equipment	30
	Connecting an External IR Receiver	30
	Connecting to AC Power	31
	Turning on the Power	31
	Lens Adjustments	31
	Focus and Zoom	31
	Lens Shift	31
	Changing the OSD Language	33
	Adjusting the Picture Orientation	33
	Rear Projection	33
	Ceiling Mode	33
	Installing and Adjusting the CineWide Anamorphic Lens	34
4.	Operation	37
	Selecting Video Memory	37
	Selecting an Aspect Ratio	37
	Selecting An Input Source	37
	Using Picture-In-Picture (PIP)	38
	Using the On-Screen Menus	39
	Main	41
	Advanced	51
	System	57
	Control	61
	Language	63
	Service	64
5.	Maintenance and Troubleshooting	67
	Lamp Replacement	67
	Troubleshooting Tips	68

xii	Runco LS-3/LS-5 Installation/Operation Manual

Image 12

Runco LS-5, LS-3 operation manual Operation, Maintenance and Troubleshooting

Contents

LS-3 Series LS-5 Series LS-3 LS-3/CineWide LS-5 LS-5/CineWidePage RuncoCare Standard Two Year Limited Warranty RuncoCare Standard Features RuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of Conformity FCC Part Page Table of Contents Maintenance and Troubleshooting Operation Specifications Serial Communications Table of Contents Xiv List of Figures List of Figures Xvi Introduction About This Manual Using This Manual If you need Turn to Description, Features and Benefits Additional Features of the LS-5 Controls and Functions LS-3/LS-5 at a Glance Source LS-3/LS-5 Rear/Bottom/Top View Runco Logo Badge Page Page LS-3/LS-5 Remote Control Projector on PIP Installation Remote ControlOperation IR Reception Angles Quick Setup Installation OverviewStep Procedure For Details, Refer Installation Projector Installation OptionsInstallation Type Considerations Ambient Light Throw Distance Throw Ratios for the LS-3/LS-5 Series Vertical and HorizontalPosition Lens Shift Horizontal Lens Shift Example Only Installing the Optional CineWide Lens Mount Folded OpticsOther Considerations Installing the Fixed CineWide Base PlateDo not use the mounting screws provided with the ceiling Mounting the LS-3/LS-5 Connector Panel Access Connections toLS-3/LS-5 Connecting Source Components to the LS-3/LS-5 HDMI/DVI Connections See Figure RGB Connections Page 11. Composite and S-Video Connections RS-232 Controller Connection Connecting 12-Volt Connecting an External IRTrigger Output to External Theater Equipment Turning on the Power Lens Adjustments Connecting to AC PowerFocus and Zoom Lens Shift Zoom Out Focus Zoom Installation Changing the OSD Language Adjusting the Picture Orientation Rear Projection Ceiling Mode Installing and Adjusting the CineWide Anamorphic Lens It is extremely important that the primary lens is properly Adjusting the Lens Height and Angle Correct Lens Angle Incorrect Lens Angle Operation Selecting Video MemorySelecting an Aspect Ratio Selecting An Input Source Using Picture-In-Picture PIP Available Main and PIP Source CombinationsPIP Input Source Main Using the On-Screen Menus LS-3/LS-5 OSD Menu Structure Main LS-3/LS-5 Main Menu Aspect Ratio Settings 169 169 Narrow Native You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Operation Overscan Examples Source Select Sub-Menu Advanced LS-3/LS-5 Advanced Menu Operation X/y Color Gamut Values Color RGB Adjust Sub-Menu 10. Fine Sync Sub-Menu Operation System 11. LS-3/LS-5 System Menu 12. Source Enable Sub-Menu PBP1 PBP2 14. PIP Split-Screen Mode Control Page Language 15. LS-3/LS-5 Service Menu OSD menus are not available when in test pattern mode Operation Maintenance and Troubleshooting Lamp Replacement Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting Key Commands Serial Communications Serial Command Key Names and IR Codes RS232 Remote Button IR Code Description Keyname Set Gam.crt Operations Control Commands Function Action on unit Lit.tog Serial Commands Operation Commands Values Save.mem Source.sel = ? Satco = ? Auto.pow.off = ? Act.source Status RS-232 Error Codes Error Code LED Indication DescriptionPage LS-3/LS-5 Specifications Dimensions Weight without lensOperating Temperature Universal Power Supply LS-3/LS-5 Dimensions 1shows the LS-3/LS-5 dimensions, in millimeters Supported Signal Timings by Input Supported Timings PAL-B/G