Using the On-Screen Menus | Runco LS-3, LS-5 manual

Operation

1.Press the MENU button on the remote control or system keypad to display the Main Menu.

2.There are six menus. Press or to select a sub-menu.

3.Press or to select a sub-menu item.

4.For each sub-menu item, the currently-selected value appears in white text or is otherwise highlighted. Press or to choose a setting for that item, or press ENTER to go to another sub-menu.

5.Press MENU to return to the previous menu.

6.From the Main Menu, press MENU to turn off the OSD menu.

The LS-3/LS-5 OSD menus are arranged hierarchically, as shown in Figure 4-1.Depending on the selected input source and signal characteristics, some menu options may not be available.

4.5

Using the On-Screen Menus

Runco LS-3/LS-5 Installation/Operation Manual

39

Image 55

Runco LS-3, LS-5 operation manual Using the On-Screen Menus

Contents

LS-3 LS-3/CineWide LS-5 LS-5/CineWide LS-3 Series LS-5 SeriesPage RuncoCare Standard Features RuncoCare Standard Two Year Limited Warranty RuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance Information FCC Part Page Table of Contents Operation Maintenance and Troubleshooting Serial Communications Specifications Table of Contents Xiv List of Figures List of Figures Xvi About This Manual Introduction If you need Turn to Using This Manual Description, Features and Benefits Additional Features of the LS-5 LS-3/LS-5 at a Glance Controls and Functions Source LS-3/LS-5 Rear/Bottom/Top View Runco Logo Badge Page Page Projector on LS-3/LS-5 Remote Control PIP Remote Control InstallationOperation IR Reception Angles For Details, Refer Quick SetupInstallation Overview Step Procedure Considerations InstallationProjector Installation Options Installation Type Throw Distance Ambient Light Vertical and Horizontal Throw Ratios for the LS-3/LS-5 SeriesPosition Lens Shift Horizontal Lens Shift Example Only Folded Optics Installing the Optional CineWide Lens MountOther Considerations CineWide Base Plate Installing the FixedDo not use the mounting screws provided with the ceiling Mounting the LS-3/LS-5 Connections to Connector Panel AccessLS-3/LS-5 HDMI/DVI Connections See Figure Connecting Source Components to the LS-3/LS-5 RGB Connections Page 11. Composite and S-Video Connections Connection RS-232 Controller Theater Equipment Connecting 12-VoltConnecting an External IR Trigger Output to External Zoom Out Focus Zoom Turning on the Power Lens AdjustmentsConnecting to AC Power Focus and Zoom Lens Shift Installation Rear Projection Ceiling Mode Changing the OSD Language Adjusting the Picture Orientation It is extremely important that the primary lens is properly Installing and Adjusting the CineWide Anamorphic Lens Adjusting the Lens Height and Angle Correct Lens Angle Incorrect Lens Angle Selecting An Input Source OperationSelecting Video Memory Selecting an Aspect Ratio Main Using Picture-In-Picture PIPAvailable Main and PIP Source Combinations PIP Input Source Using the On-Screen Menus LS-3/LS-5 OSD Menu Structure LS-3/LS-5 Main Menu Main 169 Aspect Ratio Settings Narrow 169 Native You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Operation Overscan Examples Source Select Sub-Menu LS-3/LS-5 Advanced Menu Advanced Operation Color X/y Color Gamut Values RGB Adjust Sub-Menu 10. Fine Sync Sub-Menu Operation 11. LS-3/LS-5 System Menu System 12. Source Enable Sub-Menu PBP1 PBP2 14. PIP Split-Screen Mode Control Page Language 15. LS-3/LS-5 Service Menu OSD menus are not available when in test pattern mode Operation Lamp Replacement Maintenance and Troubleshooting Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting Serial Communications Key Commands RS232 Remote Button IR Code Description Keyname Set Serial Command Key Names and IR Codes Gam.crt Lit.tog Operations Control Commands Function Action on unit Operation Commands Values Serial Commands Save.mem Source.sel = ? Satco = ? Auto.pow.off = ? Act.source Status Error Code LED Indication Description RS-232 Error CodesPage LS-3/LS-5 Specifications Universal Power Supply DimensionsWeight without lens Operating Temperature 1shows the LS-3/LS-5 dimensions, in millimeters LS-3/LS-5 Dimensions Supported Timings Supported Signal Timings by Input PAL-B/G