Manuals / Runco / Home Audio / Home Theater System

Runco operation manual Connections to the, LS-3/LS-5, Connector Panel Access

Models: LS-3 LS-5

1 105

Download 105 pages 24.46 Kb

Page 40

Connections to the

Installation

3.6	Proceed as follows to connect the LS-3/LS-5 to your video sources, external controller(s)
Connections to the	– if present – and AC power.
LS-3/LS-5	When connecting your equipment:
	• Use the correct signal cables for each source.
	• Ensure that the cables are securely connected. Tighten the thumbscrews on
	connectors that have them.
Connector Panel Access ➤	Using a flat-blade screwdriver, loosen the two
	screws holding the rear compartment cover
	in place.

Then, remove the rear compartment cover by tilting it upward.

24	Runco LS-3/LS-5 Installation/Operation Manual

Image 40

Runco operation manual Connections to the, LS-3/LS-5, Connector Panel Access

Contents

LS-3Series LS-5Series LS-3 LS-3/CineWide LS-5 LS-5/CineWideHome Theater Projectors Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesWarranty Coverage Length of WarrantyRuncoCare Claim Procedure Warranty ExclusionsOnline Product Registration Extended Service OptionsLimitation of Implied Warranties Effect of Local Law Exclusion of DamagesCOPYRIGHT AND TRADEMARKS Important Safety Instructions Compliance Information DECLARATION OF CONFORMITYFCC PART INDUSTRY CANADA ICES-003PRODUCT DISPOSAL IMPORTANT RECYCLE INSTRUCTIONSPage RuncoCare Standard Two Year Limited Warranty Table of Contentsviii Floor Mounting Upright Serial Command Syntax Key CommandsOperations Commands RS-232Error CodesTable of Contents List of Figures List of Figures 1. Introduction 1.1 About This Manual1.2 Using This Manual DANGER1.3 Description, Features and Benefits format screenAdditional Features of the LS-5 Optional Accessories2. Controls and Functions 2.1 LS-3/LS-5at a GlanceSOURCE MENUZOOM RING FRONT IR SENSORFigure 2-2. LS-3/LS-5Rear/Bottom/Top View Controls and Functions6.ADJUSTABLE FEET 1. RUNCO LOGO BADGE2.REAR COVER 3.LAMP MODULE COVERPage Page 2.3 LS-3/LS-5Remote Control the projector on8.Picture Adjustment Buttons Contrast Sharpness SHARP Press to adjust sharpnessBrightness Gamma GAMMA3. Installation 3.1 Remote ControlInstallation Figure 3-1.IR Reception AnglesTable 3-1.Installation Overview 3.2 Quick SetupInstallation Table 3-2.Projector Installation Options InstallationConsiderations Estimating Throw Distance Figure 3-2.Estimating Throw DistanceTable 3-3.Throw Ratios for the LS-3/LS-5Series Ceiling InstallationFloor Installation Figure 3-3.Projector PlacementFigure 3-4.Vertical Lens Shift Example Only Installation lens or projector is used in this exampleScreen Center 0% Screen Width W3.4 Installing the Optional CineWide Lens Mount Figure 3-6.Folded OpticsInstalling the Fixed CineWide Base Plate3.5 Mounting the LS-3/LS-5 Adjusting the ProjectionFloor Mounting Upright Ceiling MountingLS-3/LS-5 Connections to theConnector Panel Access HDMI/DVI Connections See Figure Connecting Source Components to the LS-3/LS-5Figure 3-8.HDMI/DVI Source Connections Figure 3-9.RGB Connections Page Figure 3-11.Composite and S-VideoConnections InstallationDVD Player, VCR Satellite Receiver Laser Disc etc to Automation/ Control System or PC Figure 3-12. RS-232Control System ConnectionFigure 3-13. 12-VoltTrigger Output Connection Connecting to AC Power 3.7 Turning on the Power 3.8 Lens AdjustmentsFocus and Zoom Lens Shift Installation 3.9 Changing the OSD Language Adjusting the Picture OrientationRear Projection Ceiling Mode Installation 6Anamorphic Lens Base Plate 4Swell Latch Assembly3Height/Pitch Adjustment Screw, 4-40x 1/4 1Anamorphic LensAdjusting the Lens Height and Angle Installation Correct Lens Angle Incorrect Lens Angle4. Operation 4.1 Selecting Video Memory4.2 Selecting an Aspect Ratio 4.3 Selecting An Input Source4.4 Using Picture-In-PicturePIP separated by their display modes4.5 Using the On-ScreenMenus Service MainAdvanced Figure 4-1. LS-3/LS-5OSD Menu StructureMain Figure 4-2. LS-3/LS-5Main MenuTable 4-2.Aspect Ratio Settings Table 4-2.Aspect Ratio Settings continued OperationOperation Table 4-2.Aspect Ratio Settings continuedAspect You must enter a passcode to access the Save ISF Note sub-menuBelow Black Above Black Operation Operation Figure 4-6.Overscan Examples Figure 4-7. Source Select Sub-Menu OperationAdvanced Figure 4-8. LS-3/LS-5 Advanced MenuStandard for your region Table 4-3.x/y Color Gamut Values Figure 4-9. RGB Adjust Sub-Menu OperationFigure 4-10. Fine Sync Sub-Menu Operation System Figure 4-11. LS-3/LS-5 System MenuFigure 4-12. Source Enable Sub-Menu DMD Area 644x362921x518 Screen-SafeAreaFigure 4-14.PIP Split-ScreenMode OperationControl Page Language Figure 4-15. LS-3/LS-5 Service Menu Lamp Hours User Memory 1 / User Memory ISF Day Operation 5. Maintenance and Troubleshooting 5.1 Lamp ReplacementTable 5-1.Troubleshooting Chart 5.2 Troubleshooting TipsMaintenance and Troubleshooting Table 5-1.Troubleshooting Chart continued Maintenance and TroubleshootingMaintenance and Troubleshooting Serial Command Syntax 6.1 RS-232Connection and Port Configuration6. Serial Communications Table 6-1.Serial Command Key Names and IR Codes gam.crt Precede operation and command with a space op operation command CRThe command type can be one of 5 functions Table 6-2.Serial Commands Table 6-2.Serial Commands continued Table 6-2.Serial Commands continued source.selTable 6-2.Serial Commands continued satcoTable 6-2.Serial Commands continued auto.pow.offTable 6-2.Serial Commands continued act.sourceTable 6-2.Serial Commands continued statusTable 6-3. RS-232Error Codes Error CodeLED Indication DescriptionPage Table 7-1. LS-3/LS-5Specifications continued SpecificationsSpecifications Table 7-1. LS-3/LS-5Specifications continuedGeneral 7.2 LS-3/LS-5Dimensions Specifications200 4557.3 Supported Timings Table 7-2.Supported Signal Timings by InputSpecifications Specifications PAL-B/GPAL-M PAL-60