Manuals / Runco / Computer Equipment / Projector

Runco manual Connections to the Vision 85 and VHD Controller, Connector Panel Access

Models: Vision 85

1 88

Download 88 pages 13.41 Kb

Page 35

Installation

Proceed as follows to connect the VHD Controller to the Vision 85, your video sources, external controller(s) – if present – and AC power.

When connecting your equipment:

•Turn off all equipment before making any connections.

•Use the correct signal cables for each source.

•Ensure that the cables are securely connected. Tighten the thumbscrews on connectors that have them.

To access the connector panel, press the door release button so it pops out. Turn the knob clockwise or counter-clockwise and pull gently on it to open the door.

3.5

Connections to the Vision 85 and VHD Controller

Connector Panel Access

The Vision 85 is designed to receive only video input signals directly from the companion	Connecting the Projector to
VHD Controller/Processor. Connect all signal sources to the appropriate inputs on the rear	the VHD Controller

panel of the VHD. The signal from the VHD is then output to the Vision 85 projector through an HDMI cable.

You CANNOT connect signal sources directly to the Vision 85. They MUST

Note	be routed through the VHD Controller for proper operation.

Connect the HDMI and RS-232 outputs of the VHD Controller to the corresponding inputs of the Vision 85; see Figure 3-6.

RETURN	ENTER	DOWN	UP	LEFT	RIGHT		MENU	RATIO	STANDBY	ON
RETURN	ENTER	DOWN	UP	LEFT	RIGHT		MENU	ASPECT	STANDBY	ON
RETURN	ENTER	DOWN	UP	LEFT	RIGHT		MENU	ASPECT	STANDBY	ON
								RATIO
HDMI
HDMI
60Hz-50 240V-100 IN AC				TRIGGER		IR	OUT 232-RS
60Hz-50 240V-100 IN AC				TRIGGER		IR	RS-232 OUT

AC IN 100-240V 50-60Hz

Serial No

Model

Video Processor / Controller

HDMI Out

							SYSTEM CONTROL INTERFACE
		INPUTS
R/Pr	G/Y	B/Pb	H	V
							TRIGGERS
					HD1
						1	2		IR
					HD2
R/Pr	G/Y	B/Pb	H	V				WARNING: TO REDUCE THE RISK OF FIRE
R/Pr	G/Y	B/Pb	H	V					OR ELECTRIC SHOCK, DO NOT EXPOSE
									THIS APPLIANCE TO RAIN OR MOISTURE.
			SDI	Pb	Pr	Y	S-Video 1
				Pb	Pr	Y	S-Video 1
HDMI 1		HDMI 2	Option		Component Video	Video	S-Video 2	RS-232 Out	RS-232 Control

CAUTION	!
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE CENTER.

100-230VAC 50-60 Hz, 165 Watts Max

Made In USA

HDMI OUT

RS-232 OUT

Figure 3-6. Connecting the Projector to the VHD Controller

Vidikron Vision 85 Owner’s Operating Manual

23

Image 35

Runco manual Connections to the Vision 85 and VHD Controller, Connector Panel Access

Contents

1080p DLP Projectors Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Operation Table of ContentsSerial Communications Maintenance and TroubleshootingSpecifications Table of Contents VHD Controller OSD Menu Structure for Vision 1List of FiguresList of Figures Xii This Manual 1IntroductionAbout This Manual If you need Turn to Using This ManualThey also provide supplemental information Performance or cause a malfunctionDescription, Features and Benefits Optional Accessories Vision 85 at a Glance Controls and FunctionsVertical Lens Shift Vision 85 Rear Panel Wired IR 3.5-mm, mini phono jackRS-232C Input RJ-11 female connector VHD Controller Front Panel VHD Controller Front PanelInputs Component Video RCA connectorsVHD Controller Rear Panel Hdmi 1 / Hdmi 2 DigitalComLink RS-232 Output Power Input 100 to 240 VACVideo 1 / S-VIDEO Volt 750 mA Trigger OutputsVHD Controller/Vision 85 Remote Control Vision 85 Remote Control UnitCursor Buttons On / OFFENT Enter VID 1 2 / S-VID 2 5 S-Video Memory Preset Buttons ISF NT NightCust VideoNot used Vision 85 Built-In KeypadOperation 3InstallationRemote Control To install batteries in the remote controlInstallation Signals Quick SetupInstallation Overview Step Procedure For Details, Refer toAdvantages Considerations Installation ConsiderationsProjector Installation Options Installation TypeThrow Distance Position Ceiling InstallationFloor Installation Folded Optics Ceiling Mounting Inverted Adjusting the ProjectionMounting the Vision Floor Mounting UprightVHD Controller Connector Panel AccessConnections to the Vision 85 and VHD Controller Hdmi Source HD-DVD/BD/DVD Player or HD Tuner with Connecting SourceController Hdmi Connections See FigureDigital DTV RGB or Component Video Connections Digital DTV RGB or Component Video Connections See FigurePersonal Computer Analog Computer RGB Connections See FigureDVD Player, VCR Satellite Receiver Laser Disc etc Composite/S-Video/Component Video Connections See FigureEquipment Connecting a PC orOutputs to External 13 -volt Trigger Output Connection from Projector Connecting an External IR Receiver to the VHD ControllerAdjusting the Picture Orientation Turning on the Power15. Vertical and Horizontal Lens Shift Adjustments Primary Lens AdjustmentsInstalling and Adjusting the CineWide Anamorphic Lens Adjusting the Lens Height Y Anamorphic Lens Top View 4Operation Using the On-Screen MenusAspect Ratio ISF PresetsService Input SourceAspect Ratio Main MenuInput Source Aspect Ratio Description Aspect Ratio SettingsSurface, eliminating the black bars. PictureTypical Pluge Pattern for Adjusting Brightness Perform the adjustments in the order listed hereGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Typical Test Pattern for Adjusting SharpnessInformation ISF PresetsCalibration You must enter a passcode to access the Calibration menuGain/Offset Refer to ISF Night Display Color, above Service Press Menu to exit test pattern modeCode HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Standard VisionOperation On-Screen Menus for 1080i Digital or 1080p Signals Vision 85 Main Menu 1080i Digital or 1080p Sources Only Key Picture AdjustColor Temp VAC Iris Lamp Power LanguageISF Night Picture Adjust Advanced Effects of Primary Color Hue AdjustmentsWhite Balance Options HD/RGB AdjLamp Hours read-onlyRefer to Lamp Hours on Always set this option to On. Doing otherwise may disrupt Language setting Orientation Refer to Adjusting the Picture Orientation onOperation Lamp Replacement 5Maintenance and TroubleshootingSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart To Table Maintenance and Troubleshooting 6Serial Communications Serial Command SyntaxRS-232 Connection and Port Configuration Serial CommandsValue Description Min/max Stored? CommandBrightness Command Parameter Value Description Min/max Stored? Bkgnd Enter key Value Stored? DescriptionVision 85 Specifications 7SpecificationsDimensions Home Theater Calibration SpecificationsIndustry-Standard Specifications Power RequirementsVHD Controller Specifications Vision 85 Dimensions Vision 85 DimensionsPage Vidikron