Russound CAS44 manual Searching for your Code

INSTALLER

SOURCE SETUP WITH CAS-RC REMOTE CONTROL

device should in turn perform the requested function. If it does not, repeat steps

3-5, trying each code for your brand until you find a code that works. If you cannot find a code that works see “Searching for Your Code” in this manual.

6.Repeat steps 1-5 for the other devices you want to control. For future reference, write down each working device code.

Searching for your Code

Note: S1, S2, S3, S4, Vol +/-, Mute and Power are the same for any source. All other buttons are dependent upon the device code associ- ated with the source.

If your device does not respond to the remote after trying all codes listed for your brand, or if your brand is not listed, try searching for your code:

1.Press a device key once.

2.Press and hold SET until the red LED blinks twice, then release.

3.Enter 9-9-1, then the device group number (see below). The LED blinks twice.

0 Cable (Cable Converters, Video Accessories, Satellite Receivers)

1 TV (TVs)

2 VCR (VCRs, DVD players)

3 Audio (Audio Amplifiers, Audio Amp/Tuners, CD players)

4.Aim the remote at the device and press POWER. The remote sends IR codes from its library to the selected device, starting with the most popular code first. If the device responds, go to step 6.

5.If the device does not respond, press CH+. the remote will try the next code. Continue until the device responds. Press CH- to try the previous code.

6.Press SET to lock in code. To search for other device codes, repeat steps 1-5.

Checking the Codes

If you have set up the remote using the procedure in “Searching for Your Code,” you may need to find out which five-digit code is operat- ing your equipment. For example, to find out which code is assigned to your TV:

1.Press the S# key to which the TV is assigned.

2.Press and hold SET until the red LED blinks twice, then release.

3.Enter 9 9 0. The LED blinks twice.

4.To view the code’s first digit, press 1. Count the LED blinks (e.g., three blinks =3), and enter the number in the appropriate device list in step 6 of “Programming a Device.” If a code digit is 0, the LED does not blink.

5.Repeat step 4 for the remaining digits, using 2 for the second digit, and so on.

6.To check for other device codes, repeat steps 1-5, using the appropriate S# key.

Using Learning

The CAS-RC includes a Learning feature so you can add functions that are unique to your home entertainment devices (e.g., VCR Tracking Up or Down). The following precautions apply.

•The original remote controls must be in working order for learning to work properly.

•Learned keys are mode specific, so each one can store a unique function for each mode.

•Do not use the following keys for learning: Device Keys, SET, BACK, or Record.

•Learning capacity is approximately 40 to 100 keys, depending on the code being learned.

•Certain device codes are not learnable including multi-frequency types, some high frequency ones, and other unusual formats.

•For optimum learning, avoid high levels of ambient light such as nat- ural sunlight or energy-efficient fluorescent lights.

•Have the original remote controls handy before programming learn- ing.

Programming a learned key

Note: If more than 15 seconds pass between key presses, the remote exits programming.

1.Press and hold SET until LED flashes twice.

2.Press 9 7 5.

3.Press a device key once (e.g., S1, S2, S3, S4) to assign a mode for learning.

4.Place the CAS-RC head-to-head (about 2” apart) from your original remote control. Also locate the key (on original remote control) that will serve as the teaching function.

5.On the CAS-RC, press a key where the learned function will be stored.

6.On the original remote, press and hold the the key to be learned. The CAS-RC LED will turn off.Continue holding the key on the original remote until the CAS-RC LED blinks twice.

Note: If the LED displays one long blink, a learning error has occurred. Try repeating this step again until a successful capture occurs. If the function is still not captured, press and hold SET to exit programming. Review the learning precautions listed above, or the Troubleshooting tips below, before beginning again at step 1.

7.To program another key for the same source, repeat steps 5-6. To program another device, repeat steps 1-6. Press and hold SET to exit programming.

Deleting a single learning key

1.Select a source.

2.Press and hold SET until the LED flashed twice.

NOTE: If more than 15 seconds passes between key presses, the remote exits programming.

3.Press 9 7 6.

4.Press the key (twice) containing the learned function to be delet- ed. The remote blinks twice.

5.Repeat steps 2-4 for another key on the same source, or press and hold SET to exit programming.

Deleting all learned keys in a specific mode

1.Press and hold SET until the LED blinks twice.

Note: if more than 15 seconds pass between key presses, the remote exits programming.

2.Press 9 7 6.

3.Press a device key twice (S1, S2, S3, S4) to delete all the learned keys for that mode. The LED blinks twice.

4.Repeat steps 1-3 for another set of keys for a device, or press and hold SET to exit programming.

27