Load paper with the print side facing up | Samsung ML-1610 instruction

3Load paper with the print side facing up.

2

Make sure that all four corners are flat in the tray.

4Pay attention not to overload paper. Paper overloading may cause paper jams.

5Pinch the rear guide to adjust for the paper length and pinch the side guide and slide it to the left flush against the paper.

Notes:

•Do not push the width guide far enough to cause the material to warp.

•If you do not adjust the width guide, it may cause paper jam.

SETTING UP YOUR PRINTER 2.8

Image 26

Samsung ML-1610 manual Load paper with the print side facing up

Contents

ML-1610 Series About the User’s Guide Contents Cleaning the Outside Cleaning the Inside Redistributing Toner Replacing the Toner Cartridge Important Precautions and Safety Information 17SAVE These Instructions Environmental and Safety Consideration Ozone Safety Radio Frequency Emissions Declaration of Conformity European Countries Page Introduction Up to 16 ppm in A4 17 ppm in Letter Special FeaturesYou can print at 600 dots per inch dpi You can print in Windows 98/Me/2000/XP Printer Driver Features Feature Printer Driver Printer Components Front View Rear View Understanding the Control Panel On Line/Error and Toner Save LEDsSee Troubleshooting Error Messages on Description Cancel button Function Description Setting Up Your Printer Components may differ from one country to another UnpackingPaper Cover a Clearance Space Selecting a LocationCarefully remove all of packing tape from the printer Installing the Toner Cartridge Grasp the front cover and pull it toward you to open Setting UP Your Printer Setting UP Your Printer Loading Paper You can load approximately 150 sheets of paper in the tray Load paper with the print side facing up Connecting a Printer Cable Turning the Printer on Demo page shows the printer’s current configuration Printing a Demo Various Linux See Software User’s Guide Installing Printer SoftwareSystem Requirements Setting UP Your Printer Using Print Materials Choosing Paper and Other Materials Paper Type Input Source/Capacitya Paper Tray Manual Feed Type, Input Sources and CapacitiesGuidelines for Paper and Special Materials Plain paper Only use labels recommended for laser printers Using Print Materials Using the Tray Verifying the Output Location Using Manual Feed Mode Repeat this step for every page to be printed Printing on Special Materials Using Print Materials Press the Cancel button on the control panel Canceling a Print JobThere are two ways to cancel a print job Double-click this icon to view Queue of the print jobs Maintaining Your Printer Maintaining the Toner Cartridge Toner cartridge storage Redistributing Toner Maintaining Your Printer Using the Toner Save Mode Replacing the Toner Cartridge Cleaning the Inside Cleaning the PrinterCleaning the Outside Cleaning inside the printer Maintaining Your Printer Transfer Roller Consumables and Replacement PartsItems Yield Average Pick-up Roller Solving Problems Line/Error LED is on Troubleshooting ChecklistCheck Solution Solving General Printing Problems Problem Possible Cause Solution Software User’s Guide. Try printing a But are blank Defective or out Toner Text is wrongGarbled, or Clearing Paper Jams Paper Exit Area Solving Problems Paper Feed Area Around the Toner Cartridge Tips for Avoiding Paper Jams Solving Print Quality ProblemsPrint Quality Checklist Solving Print Quality Problems Print 4.6. Contact your service representative Scratched. Install a new toner cartridgeDirty. Clean the LSU. See Cleaning the Inside on Change to a lighter weight pages. See Paper Problem Solution Wrinkles or Black pages Curl Poor Image quality Toner cartridge and install a new one. See Troubleshooting Error MessagesLED pattern Possible Problems and Solutions File in Use message Common Windows ProblemsProblem Possible Cause and Solution Appears during Common Linux Problems /etc/printcap file That would result in a cropped output Memory usage Am trying to print aRotated and cropped White nothing is Your software vendor to inform them of the issue Errors Owning the spooler daemon On my PCL or SPLError messages printing Able to print Specifications Printer Specifications Paper Specifications 80 % RH Printer SpecificationsSpecifications and Description Paper Specifications Overview 60 to 120 g/m2 bond 16 to 32 lb Maximum size Legal Size mm/in.a Weight CapacitybSupported Sizes of Paper Guidelines for Using Paper Symptom Problem with Solution Paper Paper Output Capacity Paper SpecificationsCategory Specifications Output Tray Capacity Printer and Paper Storage Environment Index USB cable, connect Software User’s Guide Installing Printer Software in Windows Sharing the Printer Locally Installing Printer Software in Windows Installing Printer Software in Windows Choose the type of installation Changing the Software Language Reinstalling Printer Software Removing Printer Software Select your printer driver from the Name drop-down list Printing a DocumentBasic Printing Orientation Printer SettingsLayout Tab Layout Options Size Paper TabCopies Scaling Graphics Tab ResolutionToner Save Mode Darkness Printer Tab Extras TabAbout Tab Using a Favorite Setting Using Help Advanced Printing Printing Multiple Pages on One Sheet of Paper N-Up Printing Printing Posters Printing a Reduced or Enlarged Document Fitting Your Document to a Selected Paper Size Using WatermarksUsing an Existing Watermark Deleting a Watermark Creating a WatermarkEditing a Watermark Watermark section. The Edit Watermark window appears Creating a New Page Overlay Using OverlaysWhat is an Overlay? Click Delete Overlay Using a Page OverlayDeleting a Page Overlay Windows 9x/Me Setting Up a Host ComputerSetting Up a Client Computer Windows NT 4.0 or higher Using Status Monitor Installing Status MonitorOpening the Troubleshooting Guide → your printer driver name → Troubleshooting Guide Changing the Status Monitor Program Settings Following window opens Supported OS Using Your Printer in LinuxSystem Requirements Recommended Capacities Installing the Printer Driver Changing the Printer Connection Method Select Complete uninstall and then click Uninstall Using the Configuration ToolUninstalling the Printer Driver Changing Llpr Properties Language, change 4 Layout properties, set Rev.1.00