Cancel button, Function Description | Samsung ML-1610 specs

LED	Description

If you press the Cancel button in Ready mode, this LED is on and the Toner Save mode is enabled.

If you press this button once again, this LED is off and the Toner Save mode is disabled.

If the On Line/Error and Toner Save LEDs blink, your system has some problems.

To solve the problem, see “Troubleshooting Error Messages” on page 5.16

1

Cancel button

Function	Description

Printing demo page	In Ready mode, press and hold this button for about 2
	seconds until all LEDs blink slowly, and release.

Manual feeding	Press this button each time you load a sheet of paper in the
	tray, when you select Manual Feed for Source from your
	software application.
	For detailed information, see “Using Manual Feed Mode” on
	page 3.7.

Canceling print job	Press this button during printing. The On Line/Error LED
	blinks while the print job is cleared from both the printer
	and the computer, and then return to Ready mode. This
	may take some time depending on the size of the print job.
	In Manual Feed mode, you can’t cancel the print job by
	pressing this button.
	For detailed information, see “Using Manual Feed Mode” on
	page 3.7.

Toner Save mode	In Ready mode, press this button to turn the Toner Save
on/off	mode on or off.
	For detailed information, see Software User’s Guide and
	page 4.5.

INTRODUCTION 1.7

Image 18

Samsung ML-1610 manual Cancel button, Function Description

Contents

ML-1610 Series About the User’s Guide Contents Cleaning the Outside Cleaning the Inside Redistributing Toner Replacing the Toner Cartridge Important Precautions and Safety Information 17SAVE These Instructions Environmental and Safety Consideration Ozone Safety Radio Frequency Emissions Declaration of Conformity European Countries Page Introduction Up to 16 ppm in A4 17 ppm in Letter Special FeaturesYou can print at 600 dots per inch dpi You can print in Windows 98/Me/2000/XP Printer Driver Features Feature Printer Driver Printer Components Front View Rear View Understanding the Control Panel On Line/Error and Toner Save LEDsSee Troubleshooting Error Messages on Description Cancel button Function Description Setting Up Your Printer Unpacking Paper Cover aComponents may differ from one country to another Selecting a Location Carefully remove all of packing tape from the printerClearance Space Installing the Toner Cartridge Grasp the front cover and pull it toward you to open Setting UP Your Printer Setting UP Your Printer Loading Paper You can load approximately 150 sheets of paper in the tray Load paper with the print side facing up Connecting a Printer Cable Turning the Printer on Demo page shows the printer’s current configuration Printing a Demo Installing Printer Software System RequirementsVarious Linux See Software User’s Guide Setting UP Your Printer Using Print Materials Choosing Paper and Other Materials Paper Type Input Source/Capacitya Paper Tray Manual Feed Type, Input Sources and CapacitiesGuidelines for Paper and Special Materials Plain paper Only use labels recommended for laser printers Using Print Materials Using the Tray Verifying the Output Location Using Manual Feed Mode Repeat this step for every page to be printed Printing on Special Materials Using Print Materials Canceling a Print Job There are two ways to cancel a print jobPress the Cancel button on the control panel Double-click this icon to view Queue of the print jobs Maintaining Your Printer Maintaining the Toner Cartridge Toner cartridge storage Redistributing Toner Maintaining Your Printer Using the Toner Save Mode Replacing the Toner Cartridge Cleaning the Printer Cleaning the OutsideCleaning the Inside Cleaning inside the printer Maintaining Your Printer Transfer Roller Consumables and Replacement PartsItems Yield Average Pick-up Roller Solving Problems Troubleshooting Checklist Check SolutionLine/Error LED is on Solving General Printing Problems Problem Possible Cause Solution Software User’s Guide. Try printing a Text is wrong Garbled, orBut are blank Defective or out Toner Clearing Paper Jams Paper Exit Area Solving Problems Paper Feed Area Around the Toner Cartridge Solving Print Quality Problems Print Quality ChecklistTips for Avoiding Paper Jams Solving Print Quality Problems Print 4.6. Contact your service representative Scratched. Install a new toner cartridgeDirty. Clean the LSU. See Cleaning the Inside on Change to a lighter weight pages. See Paper Problem Solution Wrinkles or Black pages Curl Poor Image quality Troubleshooting Error Messages LED pattern Possible Problems and SolutionsToner cartridge and install a new one. See File in Use message Common Windows ProblemsProblem Possible Cause and Solution Appears during Common Linux Problems /etc/printcap file That would result in a cropped output Memory usage Am trying to print aRotated and cropped White nothing is Your software vendor to inform them of the issue Errors Owning the spooler daemon On my PCL or SPLError messages printing Able to print Specifications Printer Specifications Paper Specifications Printer Specifications Specifications and Description80 % RH Paper Specifications Overview Size mm/in.a Weight Capacityb Supported Sizes of Paper60 to 120 g/m2 bond 16 to 32 lb Maximum size Legal Guidelines for Using Paper Symptom Problem with Solution Paper Paper Output Capacity Paper SpecificationsCategory Specifications Output Tray Capacity Printer and Paper Storage Environment Index USB cable, connect Software User’s Guide Installing Printer Software in Windows Sharing the Printer Locally Installing Printer Software in Windows Installing Printer Software in Windows Choose the type of installation Changing the Software Language Reinstalling Printer Software Removing Printer Software Printing a Document Basic PrintingSelect your printer driver from the Name drop-down list Orientation Printer SettingsLayout Tab Layout Options Size Paper TabCopies Scaling Graphics Tab ResolutionToner Save Mode Darkness Extras Tab About TabPrinter Tab Using a Favorite Setting Using Help Advanced Printing Printing Multiple Pages on One Sheet of Paper N-Up Printing Printing Posters Printing a Reduced or Enlarged Document Using Watermarks Using an Existing WatermarkFitting Your Document to a Selected Paper Size Deleting a Watermark Creating a WatermarkEditing a Watermark Watermark section. The Edit Watermark window appears Using Overlays What is an Overlay?Creating a New Page Overlay Using a Page Overlay Deleting a Page OverlayClick Delete Overlay Windows 9x/Me Setting Up a Host ComputerSetting Up a Client Computer Windows NT 4.0 or higher Using Status Monitor Installing Status MonitorOpening the Troubleshooting Guide → your printer driver name → Troubleshooting Guide Changing the Status Monitor Program Settings Following window opens Supported OS Using Your Printer in LinuxSystem Requirements Recommended Capacities Installing the Printer Driver Changing the Printer Connection Method Using the Configuration Tool Uninstalling the Printer DriverSelect Complete uninstall and then click Uninstall Changing Llpr Properties Language, change 4 Layout properties, set Rev.1.00