TROUBLESHOOTING
Self-diagnostics check list
LED | Item |
|
|
Ice Maker Sensor Error | |
|
|
| |
|
|
|
|
|
|
Ice Maker Error | |
|
|
|
|
| |
|
|
| |
|
|
|
|
|
|
|
|
Ice Room Sensor Error | |
|
|
|
|
Ice | |
|
|
|
|
| |
|
|
Water |
Panel Main communication Error |
|
| Trouble contents | Diagnostic method |
| ||||
|
|
|
|
| ||||
Display error : separation of sensor housing | When checking the voltage of MAIN PCB CN90 | |||||||
#8 CN90#4 : should be between 4.5V~1.0V. | ||||||||
part, contact error, disconnection, short |
|
|
|
| ||||
When checking the voltage of MAIN PCB |
| |||||||
circuit |
|
|
|
| ||||
|
|
| CN30#6 CN76#1: should be between 4.5V~1.0V | |||||
Display error of detecting temperature of | ||||||||
|
|
|
| |||||
sensor: more than 149 | (+65°C) or less |
|
| |||||
When checking the voltage of MAIN PCB |
| |||||||
than |
| CN30#8 CN76#1 : should be between 4.5V~1.0V | ||||||
|
| |||||||
Display error during operation of applicable | Voltage of MAIN PCB CN76#4(Orange) | |||||||
fan motor : Feed Back signal line contact | CN76#1(Gray) should be between 7V~12V | |||||||
error, separation of motor wire, motor error | ||||||||
|
| |||||||
Display error : ice making kit is harvested | After replacing ice maker, check the operation | |||||||
more than 3 times and level error | by turning the appliance ON again. |
| ||||||
** Apply to the applicable Ice Maker model. |
| |||||||
|
|
|
| |||||
|
| |||||||
Display error : separation of fresh food compartment defrost heater | After separating MAIN PCB CN70,CN71 from PCB, check the resistance value | |||||||
housing part, contact error, disconnection, short circuit or temperature | between CN70 White CN71 Orange should be 102(441) ohm | 7%. | ||||||
fuse error. Display error : the defrosting does not finish though fresh food | (resistance value is varied by the input power) |
| ||||||
compartment defrost is heating continuously for more than 80 minutes. | Check 0 Ohm : heater short, | Ohm : wire / bimetal Open. |
| |||||
|
|
|
|
| ||||
|
|
|
| When checking the voltage of MAIN PCB | ||||
Display error : sensor housing separation, | CN31#1 #4 : should be between 4.5V~1.0V. | |||||||
contact error, disconnection, short circuit |
|
|
|
| ||||
When checking the voltage of MAIN PCB |
| |||||||
Display error by detecting temperature of |
| |||||||
CN30#3 CN76#1: should be between 4.5V~1.0V | ||||||||
sensor: more than 149 | (+65°C) or less |
|
|
|
| |||
When check the voltage of MAIN PCB |
| |||||||
than |
|
| ||||||
| CN30#4 CN76#1: should be between 4.5V~1.0V | |||||||
|
|
|
| |||||
|
|
| ||||||
Display error during operation of applicable | Voltage of MAIN PCB CN76#3(Yellow) |
| ||||||
fan motor : Feed Back signal line contact | CN76#1(Gray) should be between 7V~12V. | |||||||
error, motor wire separation, motor error | ||||||||
|
|
|
|
| ||||
Display error during operation of applicable | Voltage of MAIN PCB CN76#5(SkyBlue) | |||||||
fan motor : Feed Back signal line contact | ||||||||
CN76#1(Gray) should be between 7V~12V. | ||||||||
error, motor wire separation, motor error | ||||||||
|
|
|
|
| ||||
Display error : sensor housing separation,contact error, | When check the voltage of MAIN PCB |
| ||||||
disconnection, short circuit. |
|
| ||||||
Display error by detecting temperature of sensor: more | CN31#3 CN76#1: should be between 4.5V~1.0V | |||||||
than 149 | (+65°C) or less than | |||||||
|
| |||||||
Display error : separation of freezer compartment defrost heater housing | After separating MAIN PCB CN70,CN71 from PCB, check the | |||||||
part , contact error, disconnection, short circuit or temperature fuse error. | resistance value between CN70 brown CN71 Orange should be | |||||||
Display error : the defrosting does not finish though fresh food compartment | 55(115v)ohm 7%. (resistance value is varied by input power) | |||||||
compartment defrost is heating continuously for more than 70 minutes. | Check 0 Ohm : heater short, | Ohm : wire / bimetal Open. | ||||||
Display error during operation of applicable fan motor : | Voltage of MAIN PCB CN76#2(Black) |
| ||||||
Feed Back signal line contact error, motor wire separation, |
| |||||||
motor error |
|
|
| CN75 : should be between 6V~12V. |
| |||
|
| |||||||
Display error when open error is detected by damper | After separating MAIN PCB CN91from PCB, check the resistance | |||||||
heater : separation of Damper Heater housing part, | value between Black | brown wire should be 145 ohm | 7%. | |||||
contact error, disconnection, short circuit | Check 0 Ohm : heater short, | Ohm : wire / bimetal Open. | ||||||
|
|
|
|
| ||||
Display error : separation of sensor housing, contact error, | When checking the voltage of MAIN PCB | |||||||
disconnection, short circuit. |
| |||||||
Display error by detecting temperature of sensor: more than 149 | CN30#9 CN76#1 : should be between 4.5V~1.0V. | |||||||
(+65°C) or less than |
| |||||||
|
| |||||||
Display error when open error is detected by Water Tank | After separating MAIN PCB CN79 from PCB, check the resistance | |||||||
Heater : separation of Water Tank Heater housing | value between Black | brown wire should be 72 ohm 7%. | ||||||
part,contact error, disconnection, short circuit | Check 0 Ohm : heater short, | Ohm : wire / bimetal Open. | ||||||
|
|
|
|
| ||||
Display |
|
|
|
| ||||
MICOM MAIN | LOAD communication error | Actually, it is desirable to recheck the condition with | ||||||
MICOM MAIN | PANEL communication error | the oscilloscope(1G Hz) after replacing Main and | ||||||
Panel PCB. |
|
|
| |||||
equivalent with the right value |
|
|
| |||||
|
|
|
| |||||
|
|
|
|
|
|
|
|
51