Setting of alarm, Alarm SET Hold Time | Samsung SDM-090MP, SDM-090P

Digital Multiplexer SDM-090(P)

5. Setting of alarm

Set operation when alarm occurs.

The following screen is displayed if pressing the “ENTER” button with the blinking indication placed at the “5.ALARM SET” by pressing the “MOVE” button on the main menu screen:

[ALARM SET]

HOLD TIME	01	MIN
	00	SEC
REC TYPE	NOR

ALARM INPUT OFF

- The blinking character moves if pressing →“ ”, “→” button.

-The setting value is changed if pressing “ →”, “→” button. HOLD TIME : 00 ~ 30 (MIN)

00 ~ 59 (SEC)

✴The 00 MIN 00 SEC means a manual mode (perform operation for the time the alarm

input enters into).

REC TYPE: NOR ↔ TL V

¥Set a record mode when alarm occurs. ALARM INPUT: OFF ↔ N.O ↔ N.C ↔OFF

¥Set according to the output of alarm sensor connected to the alarm input terminal on the rear side of this unit.

¥OFF: When no alarm input exists.

¥N.O: When alarm input is ACTIVE LOW.

¥N.C: When alarm input is ACTIVE HIGH.

-The changed setting value is stored if pressing the “SET” button and you can return to the main menu.

5-9

Image 47

Samsung SDM-090MP, SDM-090P manual Setting of alarm, Alarm SET Hold Time, REC Type NOR Alarm Input OFF, REC Type NOR ↔ TL

Contents

Digital Multiplexer Digital Multiplexer SDM 090P Do Not Expose This Equipment To Rain or Moisture Important Safeguards Digital Multiplexer SDM-090P Digital Multiplexer SDM-090P Contents Viii Occurrence and Handling of Alarm Chapter Introduction IntroductionPage Triplex Name of parts and FunctionMulti Screen REC Check Enter RESET/ERASEList Menu Rear Panel VCR IN/OUT BNC Installation Physical & Environmental Preparing for the Installation Precautions when Installing 15Cm Digital Multiplexer SDM-090P Unpacking Connecting to Other Devices Connecting to normal VCR and Monitor Connecting to Other Devices Connecting to S-VHS VCR and S-VHS Monitor Connecting to Time Lapse VCR Connecting to Alarm Sensor PIN Number Remote Control by connecting to PC2TXDTRANSMITTEDDATA 3RXDRECEIVEDDATA 5SGSIGNALGROUND CH4 CH5 CH6 CH7 CH8 CH9 Multi Screen REC CHECK/PB Through LIVE/PB Triplex PIP ResetAscii CH1 CH2 CH3 Chapter Initial operation Turn on power switchSetup a recording channel Change it to a desiring indication mode When desiring to see in the Full screen When desiring to see in the live screen/replay screenWhen desiring to see in the Triplex screen When desiring to see in the division screen When desiring to see automatic sequential conversion screen Freeze setting of Full screen When desiring to see the stop screen Full Mode When desiring to see in the zoom screenWhen desiring to see in the PIP screen When desiring to see output of VCR as it is When desiring to see in the record screen Setting of Program Menu Duty SET Reservation OFF Record setting of each cameraREC OUT SET REC Type TLV REC Duty SET CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 REC Type NOR ↔ TLV Setting of display mode PB Display ALL Spot OUT Cvbs PIP Size Sequence Loss Detect Loss Info Alarm InfoALL Alarm S/W Time CH1 02 CH2 CH3 02 CH4 CH5 02 CH6 CH7 02 CH8 CH9 Sequence Title SET Setting of title by channel YY/MM/DD MM/DD/YY DD/MM/YY 01/04/01 123001 YY/MM/DD Hhmmss DATE/TIME SET Display Type REC Type NOR ↔ TL Setting of alarmAlarm SET Hold Time REC Type NOR Alarm Input OFF System SET Baud Rate System settingPassword Change Alarm Buzzer OFF Loss Buzzer Summer Time Password Change Password Check NEW Password Confirm +++++++++++++++++ + - - - - + Recording Digital Multiplexer SDM-090P Frame Normal record mode Weight value REC Duty record Time Lapse record mode REC Duty Alarm weight value recordReservation record Alarm, loss Digital Multiplexer SDM-090P Screen conversion Alarm occurrence conditionsAlarm release Alarm record VCR Trig Alarm signal standard ALARM/LOSS List YY/MM/DD Hhmmss Alarm/Loss list reference Operation in video loss Appendix a Appendix a Specifications Auto Switcher Outside Drawing Appendix B Appendix B Checking points in trouble When S-VHS record is not performed