15Cm | Samsung SDM-090P, SDM-090MP manual

Digital Multiplexer SDM-090(P)

¥ Place the unit on a flat surface and

15Cm

maintain temperature properly. Allow 15 cm of clearance between the rear panel and the wall.

¥ Be careful not to drop any conductive materials into the hole for ventilation

¥When replacing built-in fuse, be sure

to turn the power off, and unplug the unit.

¥ Avoid locating the unit where direct sunlight will fall, and maintain it cool. Keep tools and equipment away from people so that they would not be hurt.

¥ Power Outlet should be grounded 2P(or 3P)Type.

2-3

Image 20

Samsung SDM-090P, SDM-090MP manual 15Cm

Contents

Digital Multiplexer Digital Multiplexer SDM 090P Do Not Expose This Equipment To Rain or Moisture Important Safeguards Digital Multiplexer SDM-090P Digital Multiplexer SDM-090P Contents Viii Occurrence and Handling of Alarm Chapter Introduction IntroductionPage Name of parts and Function Multi ScreenREC Check Triplex RESET/ERASE ListMenu Enter Rear Panel VCR IN/OUT BNC Installation Preparing for the Installation Physical & Environmental Precautions when Installing 15Cm Digital Multiplexer SDM-090P Unpacking Connecting to Other Devices Connecting to Other Devices Connecting to normal VCR and Monitor Connecting to S-VHS VCR and S-VHS Monitor Connecting to Time Lapse VCR Connecting to Alarm Sensor PIN Number Remote Control by connecting to PC2TXDTRANSMITTEDDATA 3RXDRECEIVEDDATA 5SGSIGNALGROUND Multi Screen REC CHECK/PB Through LIVE/PB Triplex PIP Reset AsciiCH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 Chapter Turn on power switch Setup a recording channelChange it to a desiring indication mode Initial operation When desiring to see in the Full screen When desiring to see in the live screen/replay screenWhen desiring to see in the Triplex screen When desiring to see in the division screen When desiring to see automatic sequential conversion screen When desiring to see the stop screen Freeze setting of Full screen Full Mode When desiring to see in the zoom screenWhen desiring to see in the PIP screen When desiring to see in the record screen When desiring to see output of VCR as it is Setting of Program Menu Duty SET Reservation OFF Record setting of each cameraREC OUT SET REC Type TLV REC Type NOR ↔ TLV REC Duty SET CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 Setting of display mode PB Display ALL Spot OUT Cvbs PIP Size Sequence Loss Detect Loss Info Alarm InfoALL Alarm S/W Time Sequence CH1 02 CH2 CH3 02 CH4 CH5 02 CH6 CH7 02 CH8 CH9 Setting of title by channel Title SET DATE/TIME SET Display Type YY/MM/DD MM/DD/YY DD/MM/YY 01/04/01 123001 YY/MM/DD Hhmmss Setting of alarm Alarm SET Hold TimeREC Type NOR Alarm Input OFF REC Type NOR ↔ TL System setting Password ChangeAlarm Buzzer OFF Loss Buzzer Summer Time System SET Baud Rate Password Change Password Check NEW Password Confirm +++++++++++++++++ + - - - - + Recording Digital Multiplexer SDM-090P Normal record mode Frame Time Lapse record mode Weight value REC Duty record REC Duty Alarm weight value recordReservation record Alarm, loss Digital Multiplexer SDM-090P Alarm occurrence conditions Alarm releaseAlarm record Screen conversion Alarm signal standard VCR Trig Alarm/Loss list reference ALARM/LOSS List YY/MM/DD Hhmmss Operation in video loss Appendix a Appendix a Specifications Auto Switcher Outside Drawing Appendix B Appendix B Checking points in trouble When S-VHS record is not performed