SeTTinG THe eVenT
You can set recording options for motion, and video loss event.
motion Detection
You can set target detection region and motion, as well as the alarm signal output.
When the motion detection region is set, it detects motion within the area.
Using the mouse may help make setup easier.
1.Use the up/down buttons ($%) in <event> window to move to <motion Detection>, and press [enTeR] button.
A window of motion detection area setup appears.
!main menu
2.Use direction buttons ($%_ +) to move to a desired item, and set the value.
•Mode : Sets whether to activate motion detection.
•Sensitivity : Sets the sensitivity level of the motion detection.
•Alarm : Sets the alarm output method.
`For further information on alarm output, refer to “HDD Alarm > Alarm”. (Page 48)
•Alarm Duration : Sets the duration of alarm signal and alarm sound.
3.When the motion detection setup is done, press <OK>.
Motion Detection
|
|
|
|
|
|
|
|
|
| CH | Mode |
| Sensitivity | Alarm | Alarm Duration |
| |
| 1 | OFF | | Level10(High) | None | 10 sec | |
|
| 2 | OFF | | Level10(High) | None | 10 sec | |
|
| 3 | OFF | | Level10(High) | None | 10 sec | |
|
| 4 | OFF | | Level10(High) | None | 10 sec | |
|
|
|
|
|
|
| Motion Region | ||
|
|
|
|
|
|
|
|
|
|
|
|
| OK | Cancel |
|
|
|
Setting the motion Detection area
①Select <motion Region>.
②When “motion Region” window appears, select a channel for detection and set the area of motion detection.
• To set the area in “motion Region” window |
|
|
|
|
|
|
|
|
|
| ||||||||||||||
In the “motion Region” window, select desired region | Motion Region |
|
|
|
|
|
|
|
| |||||||||||||||
CH1 |
|
|
|
|
|
|
|
| ||||||||||||||||
from < |
|
|
|
|
|
|
|
|
|
|
| >. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| Individual |
| Apply to All CH |
|
|
| |||||
• To set the area using <individual> selection |
| OK | Cancel |
|
|
|
|
|
|
| ||||||||||||||
In the “motion Region” window, you can select cells |
|
|
|
|
|
|
|
|
|
|
| |||||||||||||
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||
individually by using <individual>. |
|
|
|
|
|
|
|
|
|
| ||||||||||||||
When selected <individual>, “motion Region” window disappears and you can select cells one by one. | ||||||||||||||||||||||||
When the motion area setup is done, | ||||||||||||||||||||||||
button on the remote control to display the “motion Region” window again. |
|
|
|
|
|
|
|
| ||||||||||||||||
- Select : Selected cell is set to be a part of motion detection area. |
|
|
|
|
|
|
| |||||||||||||||||
|
|
|
| Select |
| |||||||||||||||||||
- Unselect : Selected cell is removed from the motion detection area. |
|
| Unselect |
| ||||||||||||||||||||
- Inverse : Unselected cells are set to be the motion detection area. |
|
|
|
| Inverse |
| ||||||||||||||||||
- Menu : After selecting individual motion areas, move to the “motion Region” window. |
|
|
|
| ||||||||||||||||||||
| Menu |
| ||||||||||||||||||||||
` If selected <Apply to All CH>, selected motion area is applied to all channels. |
|
|
|
|
|
|
|
| ||||||||||||||||
|
|
|
|
|
|
|
| |||||||||||||||||
③ When the motion detection setup is done, press <OK>. |
|
|
|
|
|
|
|
|
|
|