General settings
F
1 Connect the | Figure 1 (Do not use telephone wires.) |
the DVR with the system controller (Figure 1). | |
2 Display the | (sold separately) |
| System controller |
"Displaying the general settings screen", and then | A RS485 B |
turn the |
|
The DATA SPEED "19200" indicator starts blinking.
MENU | <MAIN MENU> |
| |
| 3.GENERAL SET |
| <GENERAL SET> |
|
(J)(S)
SET> | ||
|
|
|
DATA SPEED | : | 19200 |
STATUS INFO | : | ON |
ALARM INFO | : | ON |
ADDRESS | : | 001 |
To other
A terminals
Straight cable | Cross cable |
The DVR supports straight and
•Straight type:
A straight cable connects connector "A" to "A", and "B" to "B" of the
•Cross type:
A cross cable connects connector "A" with "B", and "B" with "A" on the
3 Turn the |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
(example: 9600), and then turn the |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
6 |
| 1 |
|
| Pin number | Connector A | Connector B | |||||||||||
clockwise. |
|
|
|
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
| ||||||||||
Selections: 2400/4800/9600/19200 |
|
|
|
|
|
| 1 | Not used | Not used | |||||||||
|
|
|
|
|
|
|
|
|
|
| 2 | Not used | Not used | |||||
The "OFF" indicator of STATUS INFO starts blinking. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| 3 | A | B | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 4 | B | A | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
| STATUS INFO : | OFF |
|
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
| 5 | Not used | Not used | |||||||||||
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
| 6 | Not used | Not used | ||||||||
4Repeat the procedure for selecting the desired settings for each item.
•STATUS INFO
OFF: The status information will not be sent.
ON: The status information will be sent.
•ALARM INFO
OFF: The alarm information will not be sent.
ON: The alarm information will be sent.
•ADDRESS
The address should be between 000~127. The address is fixed, and it should match the address of the PTZ camera. Refer to the "List of
camera address" for more information. (P90) Refer to the system controller's instruction manual for more information about the control method.
5Press the EXIT/OSD button.
EXIT/OSD
Dome camera (sold separately)
Terminator switch settings
If multiple devices are connected, terminator settings are necessary at both ends. If the terminator settings are not correct, correct data will not be sent to the devices.
•Set the terminator switch on both ends (first device and last device) to "ON", and set it to "OFF" on all other devices.
SW
ON | 2 3 | 4 | ||
1 |
|
| ||
|
|
| TERMINATE | TERMINATE |
|
|
| OFF ON | OFF ON |
English
How to set 70