Pan and Tilt Settings (PAN/TILT)

DSetting zooming operation options (ZOOM)

When a motion is detected, the camera zooms in and out automatically.

1 Use the joystick lever (xy) to select [ZOOM] and use the lever (vw) to select zooming mode.

Available settings:

•OFF: Disables the auto zooming. (Initial setting)

•IN: Performs detection at the center of the screen

and zooms in along the optical axis.

•OUT: Performs detection over the full screen (except for the masked area) and zooms out along the optical axis.

•IN-MOV:Performs detection over the full screen (except for the masked area) and zooms in at the position where motion was detected.

2Select the optical zoom magnification power (RATIO) according to the zooming mode you selected. Available settings:

•IN: x1.4, x2, x2.8, x4, x5.6, x8, FULL (zooming in to the TELE end), MANU (manual setting)

•OUT: x1/1.4, x1/2, x1/2.8, x1/4, x1/5.6, x1/8, FULL (zooming out to the WIDE end), MANU (manual setting)

•IN-MOV:x1.4, x2, x2.8, x4, x5.6, x8, FULL (zooming in to the TELE end), MANU (manual setting)

Memo: When selecting “MANU”, the RATIO SETTING screen appears. While monitoring the actual image and performing zooming operation, specify the zoom magnification power, then press the [ENTER] button. The zoom magnification power value appears in the bottom left of the screen.

3Select the duration for the zooming operation (TIME) Available settings: (common to all zooming modes) 5S, 10S, 15S, 20S, 30S, 45S, 1M, 2M, 3M, 4M, 5M

(S: Second, M: Minute)

The value you can select here should be within the duration specified in the [DURATION] setting (see step E below).

ESetting the interval after which the next alarm becomes in effect (DURATION)

When a motion is detected and an alarm signal is output, another alarm signal will not be output until the duration specified in this setting has passed.

Use the joystick lever (xy) to select [DURATION] and use the lever (vw) to select the interval after which the next alarm becomes in effect.

Available settings: 5S, 10S, 15S, 20S, 30S, 45S, 1M, 2M, 3M, 4M, 5M (S: Second, M: Minute)

BSettingsensor related options other than motion

The following settings are common to the ones performed in the camera and lens settings. See their respective reference pages.

•IRIS (Page 11)

•WHITE BALANCE (Page 12)

•BLC (Page 14)

•SHUTTER (Page 16)

•APERTURE (Page 17)

•AGC (Page 17)

•GAMMA (Page 18)

•DAY/NIGHT (Page 19)

Memo: • The IRIS, SHUTTER and MOTION functions can be used in the combination shown in the table below.

IRIS

AUTO: SENSE UP (ON)

F

T

 

T

T

T

 

MANU: EI (ON)

T

F

 

T

T

E

SHUTTER

LONG

T

T

 

F

T

T

 

SHORT

T

T

 

T

F

E

 

 

 

 

 

 

 

 

MOTION

 

T

E

 

T

E

F

 

 

 

 

 

 

 

 

 

F: Function is set T: Not allowable

E: Allowable

• : When exiting individual menu, settings will be cancelled.

☞After completing setting, use the lever to move the cursor to [MENU] and select “BACK” or “END”.

bGrouping the preset positions

(SEQUENCE GROUP)

Each preset position can be assigned to a group (A to D). The group can be used for the Sequence mode to monitor multiple surveillance locations sequentially.

PRESET NO.SELECT

1:A

11:B 21:- 31:-

2:B

12:- 22:B 32:-

3:-

13:- 23:- 33:-

4:A

14:- 24:- 34:-

5:-

15:A 25:- 35:-

6:-

16:- 26:- 36:-

7:-

17:- 27:A 37:-

8:A

18:- 28:- 38:-

9:-

19:- 29:- 39:-

 

10:-

20:B 30:B 40:-

 

 

MENU

 

BACK

 

Group A

 

 

 

Group B

No. 27

No. 1

No. 30

No. 2

No. 15

No. 4

No. 22

No. 11

No. 8

 

 

No. 20

1Use the joystick lever (xy) to select [PRESET POSITION] – “SET y”, and press the [ENTER] button.

The preset map screen appears.

29