Manuals / SATO / Computer Equipment / Printer

SATO M-8400RV manual WBa, XccccYdddd, WLa, XBa, XLa, XWa

Models: M-8400RV

1 242

Download 242 pages 5.19 Kb

Page 193

Appendix A: Command Quick Reference

INSTRUCTION	DESCRIPTION							PAGE
Vbbbb	Vertical Position. Specifies a field’s vertical location down the length							Page 4-59
	of the label from the current base reference point. Units of
	measurement are dots.

							M-8400RV

		bbbb = New Vertical Position					0001-1424


WBa	Font type. Specifies the 18W x 30L dot matrix font (including							Page 4-38
	descenders).
		a	=	0	Disables auto-smoothing of font
				1	Enables auto-smoothing if expansion is greater than 3
WDHaaaaVbbbb Copy Image Area. To copy an image to another location of the label.								Page 4-31
XccccYdddd		aaaa =		Horizontal position of the top left corner of image area
		bbbb	=	Vertical position of the top left corner of image area
		cccc	=	Horizontal length of image area
		dddd =		Vertical length of image area
WLa	Font type. Specifies the 28W x 52H dot matrix font (including							Page 4-38
	decenders).
		a	=	0	Disables auto-smoothing of font
				1	Enables auto-smoothing if expansion is greater than 3
XBa	Font type. Specifies the 48W x 48L dot matrix font (including							Page 4-38
	descenders).
		a	=	0	Disables auto-smoothing of font
				1	Enables auto-smoothing if expansion is greater than 3
XLa	Font type. Specifies the428W x 48H dot matrix font (including							Page 4-38
	decenders).
		a	=	0	Disables auto-smoothing of font
				1	Enables auto-smoothing if expansion is greater than 3
XM	Font type. Specifies the 24W x 24H dot matrix font (including							Page 4-34
	descenders).
XS	Font type. Specifies the 17W x 17H dot matrix font (including							Page 4-34
	descenders).
XU	Font type. Specifies the 5W x 9H dot matrix font (including							Page 4-34
	descenders).
XWa	Font type. Specifies the 48W x 48H dot matrix font (including							Page 4-38
	descenders).
		a	=	0	Disables auto-smoothing of font
				1	Enables auto-smoothing if expansion is greater than 3
Z	Stop Code. Ends all print jobs.							Page 4-74

SATO M-8400RV

9001041 Rev. D

Page A-7

Image 193

SATO M-8400RV manual WBa, XccccYdddd, WLa, XBa, XLa, XWa

Contents

Operator and Technical Reference Manual Sato M-8400RV 8400RV Printer OPERATOR’S Manual PrefaceAppendices PrefaceTable of Contents Programming Interface Specifications UPC-A/EAN-13 Preface This page left intentionally blank Compatibility IntroductionPrinter Overview Specification General Printer Specifications8400RV Potentiometer Adjustments Matrix Fonts Character FontsUCC/EAN-128 BAR CodesPhysical Power RequirementsAccessory Optional AccessoriesSection Installation and Configuration Unpacking and Parts Identification Installation and ConfigurationSetting UP the Printer LCD Loading Labels or Tags Loading LABELS, Tags and RibbonInstallation and Configuration Installation and Configuration Loading the Ribbon Tape Ribbon Core Rewind Spindle Operator Panel LED, illuminated when there is a system fault such as LED, illuminated when ribbon motion sensor does notLED, illuminated when printer is ready to receive data Momentary switch. Pressing this key togglesRear Panel Switches and Sensors Label Sensor Adjustment Setting Printer DIP Switch ConfigurationDSW1-1 DSW1-2 DSW1-3DSW1-7 DSW1-8 DSW1-5 DSW1-6DSW2-1 DSW2-2DSW2-7 DSW2-5DSW2-8 DSW3-1 DSW3-2DSW3-6 DSW3-7 DSW3-5DSW3-8 Printer Adjustments Power on Print Darkness Setting User ModePitch Offset and Direction Print Speed AdjustmentLabel Feed Direction Sensor PositionPitch Direction Cancel Print JobAuto Online Setting Zero Slash SettingVertical Offset Setting Horizontal Offset and Direction VERT. OffsetSensor Threshold Level Backing with Label Label Backing Only 0V to Less than GAP InputLabel Only Eye Mark Less than 5V to Calendar SetIgnore CR/LF CalendarAdvanced Mode Counters Exit Advanced ModePrint Darkness Type COUNTERs Hd dsp cut life Exit ModePrint Size Print SizeDirection Potentiometer AdjustmentsOffset Print Buffer Hex Dump HEX Dump Diagnostic LabelsReceive Buffer Hex Dump Hex Dump Label Darkness Print ProceduresPrint Potentiometer Cleaning and MaintenanceSato SA070 Cleaning Kit Cleaning the Print HEAD, Platen and RollersCleaning the Print Head and Platen Supplies neededCleaning the Rollers and Guides Cleaning the SensorsReplacing the Print Head Open the Top and Side Access doorsPrint Head Mounting Screw Head Latch Connector 250V 3A Fuse Replacing the FuseThis page left intentionally blank ESCCommand Data ESCCommandESCCommand Parameter Sato Risc Programming LanguageESC Command Parameter Data Using BasicSelecting Protocol Control Codes Programming ReferenceLprint E$A Open COM19600,E,8,1,CS,DS AS #1Print Area New Base Reference Point = Maximum Print Width Label Width Label Width = 2 x 25.4 mm/in x 8 dpmm = 406 dotsNew Base Reference Point = 832 dots 406 dots = 426 dots ESCAESCA3H426V0001ESCH0050ESCV0200ESCB103100*SATO Sato Rotated Fields Command Default SettingsBase =200 Point =800 Label Feed Direction =100 Command Codes MSI Bar CodesInput to Printer Printer Output Without Incrementing UCC-128With Incrementing Special Notes Command Function Command Structure ESCBWaabbbBar Codes, Expansion ESCBW02100Bar Codes, Variable Ratio Command Structure ESCBTabbccddeeIndividual bar code symbols Code Expansion command seeYou may use only one variable ratio bar code per label Base Reference Point Command Structure ESCA3H-aaaaVbbbbESCA3H100V0050 Panel. See Printer Configuration Printer configuration until a new Base Reference PointThis command may be used more than once in a print job Current Horizontal and Vertical Print Position commands seeCharacters, Custom-Designed Command Structure Store Command ESCTabccESCK1H903F Printer InputIf the printer power is lost Character is affected by the following commandsCharacter Expansion see Character Pitch seeCharacter Expansion Command Structure ESCLaabbThis command will also affect the following commands This command will expand the following fontsUntil a new expansion command is specified Line and Box command, if used within the data stream, mayCharacter, Fixed Spacing Command StructureSpacing XM, XS, XL and XBLabel constraints or to enhance readability Character PitchCommand see Page 4-23. The character pitch is actually This command is affected by the Escl Character ExpansionCharacter Expansion command and this command together This command affects fonts U, S, M, XU, XS, XM, OA & OB seeEnd of the print job unless a reset command is sent Reset to fixed spacingCharacter, Proportional Spacing Set to proportional spacingClear Print Jobs & Memory Command Structure ESC*aSpecial Note Continuous Forms Printing Command Structure NoneCopy Image Area Command Structure ESCWDHaaaaVbbbbXccccYddddESCWDH0100V0050X0600Y0400 Image For the duplicate image seeWill not be printed Allowable ranges for these fields are as followsCommand Structure ESCNULaaaa Cutter CommandOr label at a specified interval within a print job Between each cutFonts U, S, M, OA, OB, XU, XS & XM Command Structure Font XUPitch command see Page 4-26. The default is 2 dots between Expansion command seeCustom-Designed Characters command Default fontESC$a,b,c,d Font, VectorESC$=data ESC$A,100,200,0ESC$=123456Value of 50 is used Pitch command can be used with Vector fontsFont width and height values include asenders, desenders Other spaceFonts WB, WL, XB & XL Command Structure Font WBCharacter Pitch command see Character Expansion command seeExpansion rate is at least 3 times in each direction Characters may be enlarged through the use of the EsclESCAspaceESCZ Form FeedBlank label or tag Form Overlay, Recall Form Overlay, Store Loses power, the overlay must be sent againLabel image may be stored in this memory area at a time Overlay bufferGraphics, Custom Command Structure ESCGabbbcccdataCommands. Therefore, always design and locate your graphic Expansion commandCustom graphic cannot be enlarged by the Escl Character Custom graphic is not affected by either of the RotationGraphics, PCX Command Structure ESCGPaaaaa,dataJob ID Store Simply issue an Ascii CR at the end of each text line Command, you automatically select Font S with a CharacterJournal Print Expansion of 2x2. You also establish a base reference pointESCFWaabcccc Lines and BoxesESCFWaabbVccccHdddd ESCFW02H0200Normal print direction It is recommended that all lines and boxes be specifiedMaximum allowable lengths are as follows LINE/BOXLine Feed Sato M-8400RV Mirror Image Command Structure ESCHhhhhESCVvvvvESCRMaaaa,bbbbTo be applied to a glass or other transparent surface Label #1This command can be used with the ESC% Rotate Fixed Base All data preceding the command will be mirroredReference Point command see Page 5-66. It cannot be used With the Escr Rotate Moving Base Reference Point commandOff-Line/Pause Off-Line mode as soon as the current print job is finishedTo an On-Line status see Operator Panel in of this Postnet Command Structure ESCBPn...nESCBP123456789 Print Darkness Print Length, Expanded ESC AR Resets the maximum print length to 7 178 mmEscax Sets the print length to 14 356 mm It may be included in an independent data stream to specify Print length, or until the printer is repoweredSize of the maximum print area EscaxPrint Position ESCA3 commandsBbbb Print Quantity Command Structure ESCQaaaaaaDefault As previously set in the printer configuration Placement Must be placed immediately after EscaCommand or through the Operator Panel Allowable Print Speed settings are as followsTo print duplicate of the last label printed Repeat LabelDuplicate of the previous label will be printed Cycled off and back on since printing the previous labelESC0 ESCzero Replace Data Partial EditChanges specified within the current data stream Sato M-8400RV Reverse Image Command Structure ESCaaaa,bbbbESC100,50 Orientation when designing and sending the Reverse Image Reverse image area is affected by the rotate commandsBefore the Form Overlay command in the data stream Maximum allowable settings are as followsRotate, Fixed Base Reference Point Command Structure ESC%aCommand is received Do not combine this command and the Escr Rotate commandDefault value See Page 4-70 in the same data streamRotate, Moving Base Reference Point Escn command returns to the original base reference pointNormal Direction Escn Rotated Direction EscrCustom graphic is not affected by this command. Therefore Do not combine this command and the ESC% rotate commandSee Page 4-68 in the same data stream Always design and locate your graphic image to printSequential Numbering Command Structure ESCFaaaabcccc,dd,eeESCF001-001,04,03 This command can not be used with the following commands Labels, we need 50 total labels. The commands would be asValue specified for Print Quantity see Page 4-61 should be Equal to the number of different sequential values desiredStart/Stop Label Calendar Option Commands Placement Anywhere within the data stream Default None Command Structure ESCWPabbbThen be printed on the label. This command does not change Printer’s internal clock settingSato M-8400RV Calendar Print Command Structure ESCWAelementsESCWAMM/DD/YY hhmm Sato M-8400RV Calendar Set Command Structure ESCWTaabbccddeeESCWT9101311200 Memory Card Option Commands Memory Card Function Clear Card Memory Command Structure ESC*a,bbMemory Card Function Expand Memory Area Command Structure ESCEXaStandard Print Dots Length 178 mm Expanded with Memory Card Function Fonts, TrueType Recall This command requires the Memory Card option. See your SatoExample ESCBJR1020201000004SATO Memory CardESCBJDcccccddddee...e Memory Card Function Fonts, TrueType StoreESCBJ50 byte header ESCBJD5 byte hex memory offsetdataMemory Card Function Format/Field Recall Command Structure ESCYR,aa ESC/D,bb,cc...cESCYR,01 ESC/D,01,99 Escyr Format/Field Recall command Command Structure ESCYS,aaESC/N,bb,ccMemory Card Function Format/Field Store ESCYS,01ESC/N,01,05Memory Card Function Graphics, Custom Recall Command Structure ESCGRaaaMemory Card Function Graphics, Custom Store Command Structure ESCGIabbbcccddddataEsca Memory Card Function Graphics, PCX Recall Command Structure ESCPYaaaThis command requires Memory Card option. See your Sato PCX Graphics Recall commandMemory Card Function Graphics, PCX Store ESCPIaaa,bbbbb,dataMemory Card Function Initialize Command Structure ESCBJFaaaaaaaaPrepares the card to accept data Your local Sato representative for informationMemory Card Function Slot Select Command Structure ESCCCaMemory Card Function Status PlacementMemory Card ExampleCommand Structure ESCLD,a,b,c,d,e,f,g,h,i Custom Protocol Command Codes DownloadExample ESCLD,,,%,#,&,*,~,0,0 Protocol Command codes for that parameter will be used. See Is omitted between two commas, the default Non-StandardThis command must be sent as an independent data stream Preceding the Escz Stop code. No other commands can beTwo-Dimensional Symbols Command Structure ESCBXaabbccddeeefffghh Two-Dimensional Bar Codes Data Matrix, Data FormatESCBX03080505000000001 Bit CRC Character SET Encoding Number SchemeESCDC00006000 Two-Dimensional Bar Codes Data Matrix, Print DataCommand Structure ESCFXaaabcccdddeee Two-Dimensional Bar Codes Data Matrix, Sequential NumberingPrint Data Command To print sequential numbered Data Matrix symbolsSato M-8400RV Command Structure ESCBVa,b,c,ddddddddd,eee,fff,gggg.....ESC Two-Dimensional Bar Codes MaxicodeExample ESCBV1,2,3,123456789,222,333,MESSAGEESC Padded with exclamation point characters Secondary Message field ee...e must contain exactlyRs represents Hex 1E, Gs represents Hex 1D, Eot Represents Hex 04, ESC represents Hex 1B and SpCommand Function Printer Input Two-Dimensional Bar CodesOptimum configuration Dd andee are set to all zeroes, the printer will calculateSato M-8400RV Interface Types Section Interface SpecificationsReceive Buffer Interface SpecificationsSingle Job Buffer Multi Job BufferRS232C Serial Interface PIN Direction Signal Definition RS232C Interface SignalsData Streams Cable RequirementsOn/X-Off Flow Control Host Interconnection PrinterBI-DIRECTIONAL Communications STX 2 Byte ID1 Status Byte6 Byte Label RemainingETX Status ResponseStatus Byte Definition, Bi-Com Protocol Cable Connector Printer ConnectorSignal Level Centronics Parallel InterfacePIN Direction Signal Description Accessory EXT ConnectorExternal Output Signal Types This page left blank intentionally Using the Centronics Parallel Interface Initial ChecklistESCA-DATA-ESCZ TroubleshootingUsing the RS232C Serial Interface LED LCD Audible Error Condition To Clear Message Beep Error SignalsA3H-aaaa AspaceZVbbbb BabbcccdAppendix a Command Quick Reference BXaabbccdd BWaabbbEeefffghh CSaDdee FaaaabccccFWaaHbbbb FWaabbVcccGPaaaaa GabbbcccdataHaaaa IDaaQaaaaaa PaaRMaaaa,bbbb XccccYdddd WBaWLa XBa$a,b,c,d Rotate. Fixed Base Reference Point. Rotates printing$=data Data for Vector font #Ea Aaaa,bbbb~aaaa @, nn...nWAelements WPabbbBJS GIabbbcccdd EXaGRcc PIaa,bbbbbA-12 9001041 Rev. D BAR Code Symbologies Appendix B BAR Code SpecificationsESCB0bbcccd data d Ratio ESCBD0bbcccd data d CodabarESCD0bbcccd data d Character SetCode Command Structure Ratio ESCB1bbccc* dataESCBD1bbccc* data ESCD1bbccc* dataInterleaved Two of Five I 2/5 Use the Line and Box command seeRatio ESCB2bbccc data ESCD2bbccc data= Width of narrow element in dots SymbolValue of bb Narrow Bar Width Magnification Mils Factor Mod 10 Check Digit CalculatingSteps to find the correct check digit ODD EvenCode and the human readable text below the symbol Command Structure ESCB4bbccc data ESCD4bbccc dataCheck digit is automatically calculated for EAN-8 B5bbccc data Industrial Two of FiveBD5bbccc data D5bbccc dataESCB6bbccc data Matrix Two of FiveESCBD6bbccc data ESCD6bbccc dataSee Code 128 Character Table on Page B-18 Command Structure ESCBGbbcccdd dataSubset B for 789, then shift to Subset C for ESCBDAbbccc data d ESCBAbbccc data dESCDAbbccc data d Ccc Bar height in dots DataA-Z, -, ., Space, $, /, +, % Density Ratio Dimension Char/inch MilsBar code UPC-EBookland UPC/EAN Supplements UCC-128 Command Structure ESCBIbbcccd dataB-16 9001041 Rev. D Command Structure Escbp data Data Matrix Command Structure Data FormatSequential Numbering ESCFXaaabcccdddeee Print Data ESCDCxxx...xStructure of this symbology Mode Postal Code Country Code Service Class Message Length SymbologyCommand Structure ESCBFaabbcddeeffffnnn...n Value Subset a Subset B Subset C Code 128 Character TableCode 128 Character Table Code 128 Character Table cont’d Sato M-8400RV CUSTOM-DESIGNED Character Example9001041 Rev. D C-1 ROW BIT MAP HEX Appendix C Custom Characters and Graphics9001041 Rev. D C-3 Custom Graphics Example 9001041 Rev. D C-5 C-6 9001041 Rev. D 9001041 Rev. D C-7 PCX Graphics Example Label Rewinder InstallationRemoving and Unwinding the Roll Operator Setup Appendix D Optional FeaturesLabel Cutter General OperationLabel Dispenser Routing Label Dispense OptionLabel Dispense Option is ready for use Error Description Indication Remedy Error HandlingPcmcia Memory Cards DescriptionD-6 9001041 Rev. D Calendar D-8 9001041 Rev. D Parameter Standard Setting Alternate Setting Download Command StructureDescription Download Procedure ResetAppendix E Custom Protocol Command Codes 9001041 Rev. D E-3 E-4 9001041 Rev. D