trouble shooting
WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF"
OUTLET BEFORE TROUBLE SHOOTING.
| TROUBLE |
|
| PROBABLE | CAUSE | ||||
Noisy | Operation | 1. | Incorrect | belt | tension | ||||
|
| 2. | Dry | Spindle |
|
| |||
|
| 3. | Loose | spindle | pulley | ||||
|
|
| or | motor | pulley. |
| |||
Drill | Burns. | 1. | Incorrect | speed |
| ||||
|
|
| |||||||
|
| 2. | Chips | not | coming | out | |||
|
|
| of | hole. |
|
|
| ||
|
| 3. | Dull | Drill |
|
|
| ||
|
| 4. | Feeding too slow. |
| |||||
|
| 5. | Not | lubricated, |
|
| |||
|
| 6. | Drill | running | backwards. | ||||
Drill | leads off... | 1. | Hard | grain | in | wood | or | ||
hole | not round. |
| lengths | of | cutting |
| |||
|
|
|
| ||||||
|
|
| lips | and/or | angles |
| |||
|
|
| not | equal. |
|
|
| ||
AND ALWAYS REMOVE PLUG FROM POWER SOURCE
REMEDY
1.Adjust tension. See section "Getting To Know
Your Drill Press"...BELT TENSIONING ROD.
2. Lubricate | spindle. See "Lubrication" | section, |
3. Tighten setscrews in pulleys.
1.Change speed, See section "Getting To Know
Your Drill Press". ,. DRILLING SPEED.
2.Retract drill frequently to clear chips.
3.Reshapen drill.
4.Feed fast enough...allow drill to cut.
5.Lubricate drill. See "Basic Drill Press
Operation" section.
6.Check motor rotation. See "Motor Specifications
and Electrical Requirements" section.
1.Resharpen drill correctly.
Wood | splinters on | 1. | No |
| material" |
| |||
underside, |
|
| under | workpiece. |
| ||||
Workpiece | torn | 1. | Not | supported | or |
| |||
loose | from | hand. |
| clamped | properly. |
| |||
|
| , | , i |
|
|
|
|
|
|
Drill | Binds | in | 1. | Workpiece |
| pinching | drill | ||
workpiece. |
|
| or excessive | feed |
| ||||
|
|
|
|
|
|
|
| ||
|
|
|
| pressure. |
|
|
|
| |
|
|
| 2. | Improper | belt | tension. | |||
Excessive | drill | 1. | Bent | drill. |
|
|
|
| |
runout or wobble. | 2. | Worn | spindle | bearings. | |||||
|
|
| |||||||
|
|
| 3. | Drill | not | properly |
| ||
|
|
|
| installed | in | chuck. |
| ||
|
|
| 4. | Chuck not | properly | installed. | |||
1. Use
Press Operation" section.
1.Support workpiece or clamp it.. ,See "Basic
Drill Press Operation" section.
' '_ ' "
!.Support workpiece or clamp it.. ,See "Basic
Drill Press Operation" section.
2, Adjust tension,..See section "Getting to Know
Your Drill Press"...BELT TENSION ROD.
1.Use a straight drill.
2.Replace bearings.
3, Install drill properly,..See "Basic Drill
Press Operation" section.
4.Install chuck properly,, .refer to "Unpacking
and Assembly Instructions", . .INSTALLING THE CHUCK.
19
