Lubrication, Recommended accessories, Wheel | Sears 113.21371

maintenance

WARNING: FOR YOUR OWN SAFETY, TURN SWITCH "'OFF" AND REMOVE PLUG FROM POWER SOURCE

OUTLET BEFORE MAINTAINING OR LUBRICATING YOUR DRILL PRESS,

Frequently blow out any dust that may accumulate inside the motor.

A coat of automobile-type wax applied to the table and column will help to keep the surfaces clean.

If the power cord is worn or cut, or damaged in any way, have it replaced immediately.

For motor maintenance, follow instructions furnished with motor.

r

lubrication

All of the BALL BEARINGS are packed with grease at the factory. They require no further lubrication.

Periodically lubricate the SPLINES (grooves) in the spindle and the RACK (teeth on the quill).

USE Sears Gear Case Lubricant.

1.Lower quill and spindle all the way down .. LOCK the quill,

2.Use a small stick of wood and apply lubricant around the inside of the hole in the spindle pulley.

3.Apply lubricant to RACK (teeth) on quill extending below drill press head.

For motors lubrication, follow instructions furnished with motor.

II[

recommended accessories


Drills,		Shaper		Cutters, Router		Bits	See	Catalog
Rotary		Planer			.............................			9-2745
Mortising			Chisel		Housing			9-2465
Hollow		Chisels			and Mortising	Bits	See	Catalog
Dovetailing			Attachment					9-2462
Shaper		Fence		Attachment				9-2487
Hold-Down			and		Guide			9-2457
Drill	Press		Vises		.......................		See	Catalog
Rotary		Table			.............................			9-2495
Tilt	Table		................................					9-2439
Co!let		Chuck		.............................			9-24672

Shaper Cutter				Adapter				....................	9-24832
Sanding		Drum			.....................			9-2497	-	9-2498
Hole	Saws		up	to	21/2 in.			alia	See	Catalog
Wire	Wheels up				to	4	in.	dia. max	See Catalog
Buffing		Wheels			up	to	4	in. dia. max	See	Catalog
Polishing		Wheel,			11/2" x			1 In		9-64991
Column		Collar			............................					9-2438
Power Tool Know-how								Handbooks
	Radial		Saw		............................					9-2917
	Table		Saw		.............................					9-2918

The recommended accessories listed here are current and were available at the time this manual was printed.

18

Image 18

Sears 113.21371 Lubrication, Recommended accessories, Outlet Before Maintaining or Lubricating Your Drill Press, Wheel

Contents

Drill Press only Model no113.213710 DRI LL Press with HP Motor Or power tools Attempt to Operate Your Drill Press Until Additionam safety instructions for drill pressesFor Your OWN SAFETY, do not YOU have Read and Understand Following Additional safety instructions for drill presses Unpacking checking Cutting Tool Connecting to Power Source OutletRPM Volts Catalog no Check Motor Rotation Assembly Spindle Nose Locking Collar Chuck Chuck KEY Chuck Body Installing the Depth Stop Raising the HeadScrew the Thumb Screw partways into the Depth Pointer Tighten the Quill Lock Handle Installing Motor Pulley10, Tighten the Head Lock Handle and the Quill Lock Handle Keyway Groove Assembty Mounting the Motor Excessive Tightness could Bend the Motor Mount Installing and Tensioning Belt GreaseBelt Tensioning ROD Spindle Speed Chart Getting Know Your Drill PressThumbscrew Tablelock Handle ,, locks the table to the column Getting to know your drill pressHead Lock Handle ... locks the head to the column Another WAY Removingthe Chuck Back on Operation Observe the Following Safety PrecautionsInstalling Drills Positioning Table and Workpiece Adiustments Hole LOCAT!ONBelt Tension Outlet Before Maintaining or Lubricating Your Drill Press Recommended accessoriesLubrication Wheel Trouble shooting Outlet Before Trouble Shooting Parts List for Craftsman Drill Press Model no .21371 STD Parts List for Craftsman Drill Press Model no .21371STD RPM Parts List for Craftsman Drill Press Key Parts List for Craftsman Drill Press Model no .21371 71075 Spindle ASSEMBLY, Stop Model Number Name 113.2!3710Part Inch Drill