Elevation Lock | Sears 113242502 instruction

ELEVATION LOCK

When correctly adjusted, the elevation mechanism is tocked

securely when the ELEVATION LOCK KNOB is approx one inch from the front of the saw,

After extended use, the ELEVATION LOCK SCREW and NUT may wear. which wl_ cause the iock to slip,

1, Tilt blade to 45 ° ,

2_ Remove retaining screw, using a 3/8 in wrench

3 Move LOCK WRENCH in the direction of the arrow {this will tighten the LOCK NUT) only enough to rep{ace the retaining screw in the next hole

4, If retaining screw is in last ho_e as shown, lift LOCK

WRENCH off of LOCK NUT and reposition it by rotating it CLOCKWISE

ELEVATION LOCK SCREW

.I

ELEVATION

LOCK NUT

ELEVATION

SCREW WRENCH LOCK KNOB

MAINTENANCE

WARNING: FOR YOUR OWN SAFETY, TURN SWITCH

"OFF" AND REMOVE PLUG FROM POWER SOURCE

OUTLET BEFORE MAINTAINING OR LUBRICATING YOUR SAW,

Do not allow sawdust to accumulate inside the saw.

Frequently blow out any dust that may accumulate inside the saw cabinet and the motor,

Frequently clean your cutting tools with Craftsman Gum and Pitch Remover

A coat of automobile-type wax applied to the table and the rip fence guide bar will help to keep the surfaces clean and

allow workpieces and the fence to slide more freety.

If the power cord is worn or cut, or damaged in any way, have it replaced immediately,,

Make sure the teeth of the ANTfKICKBACK pawls are always sharp,, To sharpen:

1 Remove blade guard.

2Rotate pawl toward rear of spreader so that teeth are above top of spreader

3Hold spreader with left hand and place pawl over corner of workbench,

4, Using a small round file (Smooth	Cut) sharpen the
teeth,	/

26

Image 26

Sears 113242502 owner manual Elevation Lock Screw Lock NUT Screw Wrench Lock Knob

Contents

Table SAW Remove Adjusting Keys and Wrenches Full ONE Year Warranty on Craftsman Table SawsKnow Your Power Tool Keep Work Area Clean Stability of SAW Adjustments ..... see8o Kickbacks Stores Motor SpecificationsIndicated Type Tools Lubrication Unpacking and Checking Contents Install In. long Lock Blade SquarenessLoosen Installing RIP Fence Guide Bars Among Are Thicknesses of Paper Aligning RIP Fence Adlust Indicator Adjusting RIP Scale IndicatorIndicator Installing Blade Guard Parallel 16 IN, Wrench Is on Right Always Lock IT Securely When in USEInsert When .SAWING .... USE Tilt Lock Knob Against RemovingArbor 1WORKPIECEEND Using the Miter GaugeWork Helpers Push Stick Stop Rods CrosscuttingRepetitive Cutting Compound Miter Cutting Miter CuttingBevel Crosscutting Not Attempt to Pick IT UP AS this could Endanger Your Hands Pages 2, 3, RippingBevel Ripping RIPPING, Bevel RIPPING, Resawing Push Block Ploughing MoldingCarefully Cutting Panels Install Blade Guard Immediately UponResawing Rabbeting Indicator Block Wrench Using FeatherboardsIndicator Block Miter Gauge Groove OFF and Remove Plug from Power Source OutletHeeling Marked Head Combination Square Blade TILT, or Squareness Blade to TableTeeth TOP Screw Stop Screv Elevation Lock Elevation Lock Screw Lock NUT Screw Wrench Lock Knob CAT., no CAT.. no GuardElevation Worm and Teeth Tilt Worm and Teth Cut not true at Motor fails to develop Full power. PowerRemedy Elevation hand Wheel turn hard Frequent opening Fuses or circuit Breakers Motor starts slowly Or fails to come up To full speedStarting relay in motor will not Operate CausePage Parts List STD Parts List for Craftsman 12-INCH Motorized Table SAW 30494 Parts List for Craftsman 12-1NCH Motorized Table SAWPart 3540 63062 Parts List for Craftsman 12-INCH Motorized Table SAW Key 12 13 STD Switch Assembly See Wiring DIAGRAM, 62704 Miter Gauge Assembly Pert 62594 Guard Assembly Description Extension Parts List for Craftsman 12-INCH Iiotorized Table SAW62589 60323 STD 551225 * Lockwasher, Ext,r 1/4 Service Inch Table SAW